[SNMPMibs]
1=The Recorder is nearly full. Please refer to the manual for assistance.
2=Connection lost to RAM. If the RAM is connected via a network, check the network connections.
3=The media failed to eject. Try again.
4=Failed to read from the media. Eject the media and try again.
5=Failed to write to the media. Eject the media and try again.
6=No space to write archive database. Eject the media.
7=Failed to write data from archive to file. Eject the media and try again.
8=Database files missing. Eject the media.
9=Could not write database files. Eject the media and try again.
10=Could not read database files. Eject the media.
11=Failed to initialise for archive. Eject the media and try again.
12=Failed to initialise for append. Eject the media and try again.
13=Error adding call to database. Eject the media and try again.
14=Drive not available. Eject the media and try again.
15=A call was recorded that had no activity present. Check the connection to the card.
16=A channel did not detect any activity. Check the connection to the card.
17=A call was recorded that did not stop recording. Check the connection to the card.
18=Failed to erase database from archive media.
19=Failed to erase call data from archive media.
20=Could not initialise the serial port. Restart the Recorder.
23=Unsupported archive SCSI device found. Remove the device and restart the System.
24=Drive requires manual eject. Remove the media.
25=The media removed must be reinserted. Reinsert the media.
26=Mains power lost. The UPS is now on battery. Restore mains power as soon as possible.
27=The Recorder has lost communications with the UPS. Check communications with the UPS.
28=No external time code has been received for four hours.  Check the connections to the Service Module.
29=Failed to format the media. Eject the media and try again.
30=Automatic Space Recovery has stopped due to no communications with the CMSU. Recording will soon stop. Check the CMSU.
31=The media is full.
32=Failed to synchronise with any Time Servers. Ensure the Time Synchronization settings are correct.
33=Unable to locate Parallel Slave. Check the network connections.
34=No Parallel Master. Check the Master and the network connections are ok.
35=Parallel Slave has a critical alarm. Attend to the Slave.
36=Parallel Slave has not resumed standby. Attend to the Slave.
37=Parallel Slave no longer a Parallel Slave. Reconfigure the Slave or this Recorder.
38=Ready to Resume Standby. Press Resume Standby on the Recorder Control page.
39=Master Recorder has Failed. Attend to the Master.
40=Master Recorder Connection lost. Check the network connection to this Master.
41=Slave Recorder Connection lost. Check the network connection to this Slave.
42=Parallel Master no longer a Parallel Master. Reconfigure the Master or this Recorder.
43=The media is nearly full.
44=Cannot load media for parallel append. Please eject the media and try again.
47=The License Manager has died. Automatically restarting the License Manager.
48=A power supply has failed. Replace the power supply.
49=Unable to locate a Slave. Make sure a Slave is configured as part of this Bus Group and that the network connections are ok.
50=The WN Emulator has died.  Automatically restarting the WN Emulator
51=The Remote Application Interface has died. Automatically restarting the Remote Application Interface.
52=Slave Recorder has Failed. Attend to the Slave.
64=Drive requires cleaning. Load cleaning media.
67=Media loaded. Select the required action for this media.
74=Event notifications have been temporarily halted until all clients have processed outstanding messages.
75=There is insufficient DSP resource to process all physical channels. Please add more DSP resource or remove cards.
76=Failed to load media. Eject the media and try again.
77=Autoloader communication error. Archiving aborted. Check the connections to the autoloader and restart archiving.
79=Invalid maximum age defined. Aged Call Deletion disabled. Re-enable to restart deletion.
80=A Network Interface Adapter that was fitted cannot be found by the recorder.
81=Recorder nearly full, unable to remain in Standby. Check that the Master is archiving.
82=Remote Alarm Indication signal received. Check network devices.
83=The Recorder is nearly full. Check that the Recorder is archiving.
84=The Recorder is nearly full. Check that Network Storage is working.
85=Incompatible media loaded. Eject the media.
86=Incompatible media loaded. This drive does not support VXA-2 format media. Eject the media.
87=Channel is recording at an incorrect rate. Check the BAUD rate on the card.
88=Can no longer append to this media. Callstore database has changed. Eject the media.
89=No traffic has been processed by the recorder for the timeout period - Contact the network administrator.
90=No calls have been recorded by the recorder for the timeout period - Contact the network administrator.
91=The last call recorded contained no audio - Contact the network administrator.
92=Can no longer append to this media because system was not shutdown properly. Eject the media.
93=No network adapter is bound to TCP/IP. Recorder network configuration requires modification.
94=Multiple network adapters are bound to TCP/IP. Recorder network configuration requires modification.
95=The Database has been unable to update to the latest version due to insufficient disk space. A new alarm will be raised to notify you when the Recorder has sufficient space available to complete the update.
96=There is now sufficient disk space available to complete the database update process. Please restart the Recorder when it is convenient but be aware that this could take several hours.
97=Media write error, archiving switched to standby drive. Can no longer append to this media. Eject the media.
98=The Recorder Interface Converter has died. Automatically restarting the Recorder Interface Converter
99=The Recorder has experienced an unknown error
100=Unsupported type of media loaded. Eject the media.
103=Call Authentication feature initialisation failure. Digital signing of calls cannot be performed. Please contact your supplier.
104=Call Authentication feature failed to sign a call. Please contact your supplier.
105=RAM diagnostics are enabled. This setting may hinder Recorder operation and should be disabled as soon as possible.
106=Card requires additional database fields to run correctly. The card will be disabled until the Recorder is restarted.
107=Network Storage: Connection has been lost. Check the network connection. If this is not resolved, the Recorder will stop recording.
108=Network Storage: Free space must be made available.
109=Network Storage: File access has failed. Check settings/permissions on Network Storage.
110=Network Storage: A database update is required before import can begin. Please restart the Recorder when it is convenient but be aware that this could take several hours.
111=Channel is experiencing framer errors. This can cause recording errors on this channel and detract from overall Recorder performance. Please contact your supplier for more information.
112=A channel encountered a serious error and was disabled. Please contact your supplier for more information.
113=The CTI Server has died. Automatically restarting the CTI Server.
114=CTI Server event feed has failed. Check network connections to the CTI Server.
115=An attempt has been made to enable more devices for recording than available Mitel SRC Tap licenses, calls will not be recorded for one or more devices. Please remove items from the recording enabled list or add more Tap licenses.
116=A device did not register successfully with the MLS. This device is unable to record.
117=A device did not get any events for the specified period.
118=A device did not get detect any calls over the specified period.
119=Network Storage is nearly full.
120=A filter has no writable Network Storage (primary) assigned. If this is not resolved, the Recorder will stop recording.
121=A filter has no writable Network Storage (backup) assigned. If this is not resolved, the Recorder will stop recording.
122=Filter 'All Other Calls' has no writable Network Storage (primary) assigned. If this is not resolved, the Recorder will stop recording.
123=Filter 'All Other Calls' has no writable Network Storage (backup) assigned. If this is not resolved, the Recorder will stop recording.
124=No CTI data is being received. Check connections to the CTI server.
125=CTI timing differs from Recorder time. Check time synchronisation.
126=One or more Timed Limited Licenses are about to expire.
127=One or more Timed Limited Licenses have expired.
128=Unable to record an Avaya Active call as we have exhausted our pool of recording devices.
129=No calls were recorded for the specified period.
130=Constant recording for the specified period.
131=Live Acquire buffer overrun detected due to the system being overloaded. Reduce system load and restart the Recorder.
132=Connection to Avaya AES has been lost, attempting to reconnect. Check network connections and AES Server
133=Cannot record a call as we have reached the maximum Avaya device limit for a single call.
134=Unable to record an Avaya extension as it is not properly configured on the Avaya Comms Manager.
135=No CTI calls were recorded for the specified period.
136=Constant CTI recording for the specified period.
137=CallVision[Centricity] lost CTI connection to switch. Check network connections and Centricity service.
138=Lost connection to CTI Server. Check network connections and CTI Server.
139=CTI Server lost connection to ALL event sources. Check network connections and CTI Server.
140=CTI Server lost connection to one of the event sources. Check network connections and CTI Server.
141=Unexpected error creating Avaya SSC for one or more devices. Check Alerts in event logs for more specific details.
142=PSAP CTI Server has updated the Database fields, recorder restart required.
143=An Avaya SSC recording device has been unregistered. Check for changes to the Avaya Comms Manager.
144=Lost connection to Mitel SRC.  Check the network connections and the SRC Server.
145=Filter 'CallSafe' has no writable Network Storage assigned. Until this is resolved no calls can be locked.
146=CallSafe cannot access calls on Network Storage. Check the network connection.
147=CallSafe buffer overrun detected. One or more locked calls are incomplete. Please contact your supplier.
148=The maximum number of configured RTP ports allowed in the RTP RAM has been exceeded. Please reduce the number specified.
149=Not able to allocate required number of ports for RTP RAM in the range specified.
150=Unable to bind a socket to a port for use by the RTP RAM, this port has been removed from the record list.
151=Unable to initialise OpenTrade CTI Server, no RTP ports are available! Please check your RTP RAM configuration.
152=CTI Server has run out of RTP ports to record with, please ensure a large enough range is specified in your RTP RAM configuration.
153=Unable to start Alcatel TSAPI monitor due to invalid device ID. Check device ID and restart recorder.
154=Unable to start Alcatel TSAPI monitor due to license limit exceeded. Check Alcatel licensing and restart recorder.
155=Unable to start Alcatel TSAPI monitor due to unknown error. Check Alcatel configuration and restart recorder.
156=Restart of Operating System disabled for diagnostic purposes. Operating System restart should be re-enabled for correct recorder operation.
157=Unable to register a Genesys Device. Check Genesys configuration and restart recorder.
158=A Protocol Processor requires database changes. Calls may not be recorded correctly until the Recorder is restarted.
159=Unable to record a TDM DR-Link call due to no available voice link channels. Add more channels.
160=Alcatel CTI Server configuration error. Verify configuration and restart recorder.
161=Unable to record an IP DR-Link call due to no available RTP Channels. Add more channels.
162=Alcatel IP DR-Link failure. Check TSAPI Premium Server, OXE and CTI Server config and restart recorder.
163=Alcatel IP DR-Link license limit reached, increase OXE Lock 334 count.
164=The AARAM has stopped responding.  Shutting down the AARAM for a restart.
165=Unable start Avaya TSAPI monitor. Check device configuration.
166=Unable to query the QM database. Check network and QM connection settings. Users will not sync until this is corrected.
167=Unable to sync user to QM. Check network and QM connection settings.
168=Unable to start Mitel device monitor.
169=Unable to get the device ID for an extension
170=Unable to start a monitor for an extension
171=Unable to register an extension
172=Unable to record a call due to no available recording devices
173=Unable to record a device due to no available RTP channels
174=Unable start Aastra TSAPI monitor. Check device configuration.
175=Software license expiring. Contact support
176=An Audio Search Indexer recorder search has failed, indexing will not be able to continue until this is resolved.
177=An error has occurred while attempting to index a call for audio search.
178=Failed to download a call for audio search indexing.
179=Audio Search Indexer failed to connect to the recorder, check your connection settings.
180=Audio Search Indexer failed to annotate call with audio search call ID.
181=Audio Search Indexer has found too many un-ended calls and will not be able to continue indexing until some of these have ended.
182=No free RTP channel for last Aastra call.
183=A call failed to record due to an invalid start time. Please contact your supplier.
184=Lost connection to DataRam Client. Check network connections and client.
185=No Shoretel route points configured. At least one route point must be configured for recording.
186=Unable to connect to resiliency partner
187=Siemens Trading - Lost connection to turret.
188=Windows UAC is enabled, Recorder may not function correctly. Disable UAC and restart the Recorder.
189=Send email failed
190=Attempt to save file to disk failed
191=Other report schedule errors
192=Unable to sync unit to QM. Check network and QM connection settings.
193=Immediate agent id on monitoring failed. Agent id not available until agent logs off and on again.
194=Failed to record audio stream for a trader, an audio stream has not been configured on the trader platform.
195=The recorder Quantify features are unlicensed. Please contact your supplier for more information.
196=IVDS has dropped packets. Please investigate network settings and CPU load on that machine.
197=IVDS has not captured any packets. Please investigate network and application configuration
198=A unit has one or more invalid E-Mail addresses set up. Please check configuration settings
199=E-Mail server settings are not set up. Please check configuration settings.
200=A unit has no statement period set up. Please check configuration settings.
201=Failed to send a billing E-Mail. Please check configuration settings.
202=Billing sender E-Mail address not set up. Please check configuration settings.
203=A Call Indexer recorder search has failed with the following error: ''.
204=An error has occurred while attempting to index Call ID: '' for call indexing.
205=Failed to download Call ID: '' for call indexing.
206=Call Indexer failed to connect to the recorder.
207=Call Indexer failed to annotate call with audio search call ID.
208=Call Indexer has found over '' un-ended calls and will not be able to continue indexing until some of these have ended.
209=Call Indexer cannot index calls due to receiving a 403 Forbidden response when trying to upload to the indexing server
210=There is insufficient capacity on the Hitachi Content Platform to store calls from the Call Indexer
211=The Hitachi server has denied the upload request from the Call Indexer, please check the configuration
212=Audio File cannot be found on the Hitachi Content Platform for the Call Indexer to attach metadata to
214=Not enough free RTP channels available to record BT Unified Trading turret
1001=The Recorder is full. Please refer to the manual for assistance.
1002=The Recorder can't access the call store. Is the network OK?
1003=The Recorder is unlicensed and will be shutdown. Please contact your supplier for more information.
1004=The ASPI Driver has failed. Restart the System.
1005=There is no ASPI Driver. Restart the System.
1006=The host adapter has failed. Restart the System.
1007=An Archive Drive has been removed. Check the connection to this drive.
1008=Error creating new archive database. Eject the media and try again.
1011=DSP Failure detected. Reset the DSP.
1012=Record Failure detected. Reset the DSP.
1013=A fatal error occurred installing the drivers. Restart the Recorder.
1014=A card has been removed. Restart the Recorder.
1015=A card has failed to initialise. Restart the Recorder.
1016=A card reported unmatched hardware. Restart the Recorder.
1017=The UPS is in low battery mode. Initiating Recorder shut-down.
1018=The Recorder has lost communications with the UPS whilst running on battery. Initiating Recorder shut-down.
1019=RAM has died. Automatically restarting the RAM.
1020=An unexpected error has occurred. Check the Recorder status.
1021=A Card Link Failed. Check the connections to the card.
1022=RAM has failed to startup correctly. Restart the Recorder.
1024=Unrecoverable communication failure. Archiving aborted. Check the drive connections and restart the System as soon as possible to avoid potential data loss.
1025=Out of memory. Initiating recorder restart.
1026=A card reported incorrect firmware or driver files. Please install the latest Recorder System and PCIT Firmware RBR files.
1027=A card reported a serious error. Replace the card or contact your supplier for more information.
1028=A Channel reported a buffer overrun due to the system being overloaded. If possible, reduce the number of uncompressed channels recording and restart the Recorder.
1029=The Callstore Database has failed. Recording Aborted. Please contact your supplier for more information.
1030=A card reported a Loss of Signalling multiframe alignment error. Check the connections to the card.
1031=A card reported a Loss of CRC multiframe alignment error. Check the connections to the card.
1032=A Card requires a system restart. The card will be disabled until the Recorder is restarted.
1033=The Recorder is full. Has archiving stopped?
1034=The Recorder is full. Has Network Storage stopped?
1035=An unexpected error has occurred. Check the recorder status.
1036=An unexpected error has occurred. Check the recorder status.
1037=Incompatible firmware detected. Update firmware to latest revision and restart the System.
1038=A channel has detected Loss of Signal. Check the connections to this channel.
1039=At least one Protocol Processor was not loaded due to filter string length.
1040=An internal licensing error has occurred. Please restart your recorder.
1041=CTI Server event feed has failed. Check network connections and CTI Server(s).
1042=The CTI Server has died.  Automatically restarting the CTI Server.
1043=PCIT Event Queue is overloaded. Please contact your supplier for more information.
1044=No MLS connection available. Nortel Active Recording is disabled.
1045=Frame buffer overrun detected due to the system being overloaded. Reduce system load and restart the Recorder.
1046=Screen recording CTI Server has lost connection to the Screen Recording Server.
1047=Connection to the Ekisa Configurator Service (screen recording) has been lost, attempting to reconnect.
1048=Contact closure failed to find the specified channel
1049=Intel RAID: RAID failure - see recorder event log / status for more details.
1050=Record buffer overrun detected due to the system being overloaded. Reduce system load and restart the Recorder.
1051=Software license in grace period.
1052=Software license grace period expired
1053=Lost connection to DataRam Client. Check network connections and client.
1054=Siemens Trading - Lost connection to all turrets in group.
1055=A Protocol Processor was not loaded. The version is incompatible. Please contact your supplier for more information.
1056=A fatal recording error has been detected. No traffic is being processed. Restart the Recorder.
1057=Unit channel allocation has been reset. Please correct your licensing then restart.
1058=Master channel allocation mode is different to slave. Please ensure that the setting is the same between both recorders.
1059=Traffic capture on a network adapter has failed. Check the adapter configuration and restart the Recorder.
1060=An AG has failed. Verify TETRAPOL configuration.
1061=A service is not running. Automatically restarting the service.
1062=A DataRAM client has died. Automatically restarting the DataRAM client.