Proprietary MIB Definition Internet Draft S. Whitaker Document: cambium-ptp-v1.txt Cambium Networks Ltd. Version: xx650-01-40 Friday 6th February 2015 Definitions of Managed Objects for the Cambium Point-to-Point Bridges - 650 Series Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC 2026 except that the right to produce derivative works is not granted. Abstract This memo defines a portion of the Management Information Base (MIB) for use with the Cambium Point-to-Point Bridges - 650 Series. 1. The Network Management Framework The Internet-standard Network Management Framework consists of three components. They are: STD16/RFC 1155 which defines the SMI, the mechanisms used for describing and naming objects for the purpose of management. STD16/RFC 1212 defines a more concise description mechanism, which is wholly consistent with the SMI. RFC 1156 which defines MIB-I, the core set of managed objects for the Internet suite of protocols. STD17/RFC 1213, defines MIB-II, an evolution of MIB-I based on implementation experience and new operational requirements. STD15/RFC 1157 which defines the SNMP, the protocol used for network access to managed objects. The Framework permits new objects to be defined for the purpose of experimentation and evaluation. 2. Objects Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) [4] defined in the SMI. In particular, each object is named by an OBJECT IDENTIFIER, an administratively assigned name, which specifies an object type. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. 2.1. Format of Definitions S. Whitaker [Page 1] RFC DRAFT Cambium PTP MIB February 2015 Section 4 contains the specification of all object types contained in this MIB module. The object types are defined using the conventions defined in the SMI, as amended by the extensions specified in [6,7]. 3. Overview The Cambium Point-to-Point Bridges - 650 Series uses advanced wireless technology to provide non line of sight (NLOS) ethernet communications. 3.1. Structure of MIB Objects in this MIB are arranged into groups. Each group is organized as a set of related objects. Some of the objects in this MIB are attributes which require a system reboot for new settings to take effect. When reading the MIB, these attributes will always return their current value. *** NEW SETTINGS WILL NOT BE VISIBLE UNTIL AFTER A SYSTEM RESET. *** New settings will be held in memory and activated on the next system reboot: they are not discarded or forgotten, or automatically undone. It is therefore the responsibility of the management system to keep track of new settings, and to undo any unwanted settings. The unit should not be left with partly completed configuration changes, which might be accidentally applied some time later upon a system reboot by some other unwitting manager. To undo new settings, the current (old) values may simply be read from the MIB, and then replayed back as new settings. Such an operation may be safely performed on all attributes (except the "systemReset" attribute itself) without knowledge of which attributes require a system reboot. The overall structure and assignment of objects to their groups is shown below. +-cambium | +-ptp650 | +-dfs | | | +-dfsTableNumber | +-extendedSpectrumScanning | +-dfsTable | | | +-dfsTableIndex | +-dfsMeans | +-dfsNineNinePointNinePercentiles | +-dfsPeaks | +-bridge | | | +-localPacketFiltering | +-configuration | | | +-iPv4Address | +-subnetMask | +-gatewayIPAddress | +-targetMACAddress | +-masterSlaveMode | +-maximumTransmitPower | +-antennaGain | +-cableLoss | +-eIRP | +-channelBandwidth | +-linkName | +-siteName | +-accessMethod | +-groupID | +-iPv6Address | +-iPVersion | +-iPv6AutoConfiguredLinkLocalAddress | +-iPv6PrefixLength | +-iPv6GatewayAddress | +-remoteInternetAddressType | +-remoteInternetAddress | +-subbandLowestFrequency | +-subbandHighestFrequency | +-enableTransmission | +-ethernet | | | +-mainPSUPortAutoNegotiation | +-mainPSUPortAutoNegAdvertisement | +-mainPSUPortAutoMdix | +-mainPSUPortStatus | +-mainPSUPortSpeedAndDuplex | +-dataPortWirelessDownAlert | +-useVLANForManagementInterfaces | +-vLANManagementPriority | +-vLANManagementVID | +-auxPortStatus | +-auxPortSpeedAndDuplex | +-ethernetPriorityTableNumber | +-l2CPPriorityTableNumber | +-iPDSCPPriorityTableNumber | +-mPLSTCPriorityTableNumber | +-managementPortWirelessDownAlert | +-qOSPriorityScheme | +-unknownNetworkPriorityQueueMapping | +-dSCPManagementPriority | +-dataBridgingStatus | +-mainPSUPortAllocation | +-auxPortAllocation | +-sFPPortAllocation | +-dataPortPauseFrames | +-sFPPortAutoNegotiation | +-sFPPortAutoNegAdvertisement | +-sFPPortAutoMdix | +-sFPPortStatus | +-sFPPortSpeedAndDuplex | +-auxPortPowerOverEthernetOutput | +-auxPortPowerOverEthernetOutputStatus | +-syncETracking | +-syncEEquipmentClock | +-mainPSUPortQLRxOverwrite | +-mainPSUPortSSMTx | +-sFPPortSSMTx | +-auxPortSSMTx | +-syncETrackingState | +-mainPSUPortQLRx | +-auxPortQLRx | +-sFPPortQLRx | +-mainPSUPortQLTx | +-auxPortQLTx | +-sFPPortQLTx | +-mainPSUPortSyncEMasterSlaveStatus | +-auxPortSyncEMasterSlaveStatus | +-sFPPortSyncEMasterSlaveStatus | +-mainPSUPortGigabitMasterSlaveStatus | +-auxPortGigabitMasterSlaveStatus | +-sFPPortGigabitMasterSlaveStatus | +-transparentClock | +-transparentClockVLAN | +-transparentClockVID | +-mainPSUPortAcceptedQLRx | +-auxPortAcceptedQLRx | +-sFPPortAcceptedQLRx | +-mainPSUPortSyncERxStatus | +-auxPortSyncERxStatus | +-sFPPortSyncERxStatus | +-nIDULanPortStatus | +-nIDULanPortSpeedAndDuplex | +-oOBPriorityQueueMapping | +-nIDULanPortAutoNegotiation | +-nIDULanPortAutoNegAdvertisement | +-nIDULanPortAutoMdix | +-nIDULanPortGigabitMasterSlaveStatus | +-txMABFrames | +-managementNetworkAccessEnabled | +-secondDataPortPauseFrames | +-secondDataBridgingStatus | +-transparentClockPort | +-ethernetPriorityTable | | | | | +-ethernetPriorityTableIndex | | +-ethernetPriorityQueueMapping | +-l2CPPriorityTable | | | | | +-l2CPPriorityTableIndex | | +-l2CPPriorityQueueMapping | +-iPDSCPPriorityTable | | | | | +-iPDSCPPriorityTableIndex | | +-iPDSCPPriorityQueueMapping | +-mPLSTCPriorityTable | | | +-mPLSTCPriorityTableIndex | +-mPLSTCPriorityQueueMapping | +-tDM | | | +-tDMInterfaceControl | +-tDMInterfaceStatus | +-tDMEnabledChannels | +-tdmTableNumber | +-tDMConfigurationMismatch | +-lowestTDMModulationMode | +-tdmTable | | | +-tdmTableIndex | +-tDMChannelStatus | +-tDMChannelLineCode | +-tDMChannelCableLength | +-tDMChannelLoopback | +-license | | | +-regulatoryBand | +-productVariant | +-productName | +-frequencyVariant | +-sNMPv3Enable | +-licenseVersion | +-licenseUnitSerialNumber | +-licenseIssueNumber | +-licenseCountry | +-licenseNumberOfRegulatoryBands | +-licenseBandwidthCap | +-licenseEncryption | +-licenseSecurityLevel | +-licenseGroupAccess | +-licenseOOBManagementSupport | +-licenseSFPPortSupport | +-licenseAuxiliaryPortSupport | +-licenseCapacity | +-licenseMaxNumberOfTDMChannels | +-licenseIEEE1588Support | +-licenseSyncESupport | +-licenseIPv6Support | +-licenseMinimumFirmwareVersion | +-licenseFullCapabilityTrialStatus | +-licenseRemainingTrialPeriod | +-licenseRemainingTrialPeriodAlarm | +-capacityVariantMismatch | +-licenseTDDSyncSupport | +-licenseMaxLinkRange | +-licenseTrialPeriod | +-licenseRARSupport | +-licenseRegulatoryBandsTable | | | +-licenseRegulatoryBandsTableIndex | +-licenseRegulatoryBandsList | +-management | | | +-targetRange | +-rangingMode | +-installStatus | +-installArmState | +-tFTPServerPortNumber | +-tFTPSoftwareUpgradeFileName | +-tFTPStartSoftwareUpgrade | +-tFTPSoftwareUpgradeStatus | +-tFTPSoftwareUpgradeStatusText | +-tFTPSoftwareUpgradeStatusAdditionalText | +-hTTPAccessEnabled | +-telnetAccessEnabled | +-hTTPPortNumber | +-hTTPSPortNumber | +-telnetPortNumber | +-hTTPSAccessEnabled | +-tFTPServerInternetAddressType | +-tFTPServerInternetAddress | +-lowestDataModulationMode | +-lowestSecondDataModulationMode | +-phyControl | | | +-linkSymmetry | +-userConfiguredMaxModulationMode | +-linkModeOptimization | +-txColorCode | +-rxColorCode | +-remoteMaximumTransmitPower | +-phyStatus | | | +-linkLoss | +-receivePower | +-vectorError | +-transmitPower | +-receiveChannel | +-transmitChannel | +-receiveFreqMHz | +-transmitFreqMHz | +-signalStrengthRatio | +-receiveFreqKHz | +-transmitFreqKHz | +-rawReceivePower | +-range | +-receiveModulationMode | +-transmitModulationMode | +-searchState | +-alarms | | | +-unitOutOfCalibration | +-incompatibleRegulatoryBands | +-noWirelessChannelAvailable | +-wirelessLinkDisabledWarning | +-mainPSUPortDisabledWarning | +-sFPError | +-mainPSUPortConfigurationMismatch | +-incompatibleMasterAndSlave | +-tDDSynchronizationStatus | +-auxPortDisabledWarning | +-tDDSynchronizationAlarm | +-linkModeOptimizationMismatch | +-auxPortConfigurationMismatch | +-secureModeAlarm | +-dataBridgingStatusAlarm | +-sFPPortDisabledWarning | +-sFPPortConfigurationMismatch | +-maxLinkRangeExceeded | +-nIDULanPortDisabledWarning | +-nIDULanPortConfigurationMismatch | +-portAllocationMismatch | +-secondDataBridgingStatusAlarm | +-transparentClockSourcePortAlarm | +-smtp | | | +-sMTPEmailAlert | +-sMTPServerPortNumber | +-sMTPSourceEmailAddress | +-sMTPDestinationEmailAddress | +-sMTPEnabledMessages | +-sMTPServerInternetAddressType | +-sMTPServerInternetAddress | +-snmpControl | | | +-sNMPPortNumber | +-sNMPCommunityString | +-sNMPTrapTableNumber | +-sNMPTrapVersion | +-sNMPEnabledTraps | +-enabledDiagnosticAlarms | +-sNMPSendAllTrapsAtStartup | +-sNMPTrapTable | | | +-sNMPTrapTableIndex | +-sNMPTrapPortNumber | +-sNMPTrapInternetAddressType | +-sNMPTrapInternetAddress | +-sNMPTrapReceiverEnabled | +-sntp | | | +-sNTPState | +-sNTPPollInterval | +-sNTPSync | +-sNTPLastSync | +-systemClock | +-timeZone | +-daylightSaving | +-sNTPPrimaryServer | +-sNTPPrimaryServerDeadTime | +-sNTPServerRetries | +-sNTPServerTimeout | +-sNTPServerTableNumber | +-sNTPServerTable | | | +-sNTPServerTableIndex | +-sNTPServerPortNumber | +-sNTPServerStatus | +-sNTPServerInternetAddressType | +-sNTPServerInternetAddress | +-reset | | | +-systemReset | +-versions | | | +-softwareVersion | +-hardwareVersion | +-secondarySoftwareVersion | +-bootVersion | +-pubStats | | | +-receiveDataRate | +-transmitDataRate | +-aggregateDataRate | +-wirelessLinkAvailability | +-wirelessLinkStatus | +-byteErrorRatio | +-receiveModulationModeDetail | +-dataBridgingAvailability | +-encryption | | | +-encryptionAlgorithm | +-tDDControl | | | +-tDDSynchronizationMode | +-aAAControl | | | +-userTableNumber | +-userTable | | | +-userTableIndex | +-userName | +-userRole | +-userEnabled | +-userPassword | +-syslogControl | | | +-syslogClient | +-syslogState | +-routerProtocols | | | +-microwaveAdaptiveBandwidth | +-mABNominalModulationMode | +-mABTransmissionInterval | +-mABHoldoffPeriod | +-mABMaintenanceLevel | +-useVLANForMABProtocol | +-mABProtocolVID | +-mABProtocolVLANPriority | +-mABState | +-mABNominalTransmitCapacity | +-mABCurrentTransmitCapacity | +-cableDiagnostics | | | +-cableDiagnosticsPorts | +-cableDiagnosticsControl | +-cableDiagnosticsWarning | +-cableDiagnosticsResultTableNumber | +-cableDiagnosticsResultTable | | | +-cableDiagnosticsResultTableIndex | +-cableDiagnosticsResultsDateTime | +-cableDiagPair1Results | +-cableDiagPair1Distance | +-cableDiagPair2Results | +-cableDiagPair2Distance | +-cableDiagPair3Results | +-cableDiagPair3Distance | +-cableDiagPair4Results | +-cableDiagPair4Distance | +-supplementary | | | +-longitude | +-latitude | +-altitude | 3.1.1. The dfs Group 3.1.2. The bridge Group This group contains configuration attributes for the wireless ethernet bridge (and which are not already provided by RFC 1286/1493/4188). 3.1.3. The configuration Group This mandatory group contains the objects which are applicable to the PTP unit configuration. NB: Some attributes in this group hold their new settings in memory, which will only take effect after a system reboot. 3.1.4. The ethernet Group The ethernet group contains attributes to control the operation of the local ethernet link. NB: Some attributes in this group hold their new settings in memory, which will only take effect after a system reboot. 3.1.5. The tDM Group The TDM group describes the configuration and status of E1/T1 telecom channels over the wireless when the link has been installed for TDM traffic. The group also allows loopback connections to be configured on the telecom channels. 3.1.6. The license Group This license group contains a description of the system capabilities that are controlled and managed via the systems license key. 3.1.7. The management Group 3.1.8. The phyControl Group The PHY control group contains a description of the attributes that control the behaviour and performance of the wireless links physical layer. 3.1.9. The phyStatus Group This mandatory group contains the objects which are applicable the PTP units wireless physical layer operational parameters. 3.1.10. The alarms Group This group contains objects which indicate alarm conditions. With suitable configuration, changes to the values of these attributes will cause SNMP traps and/or SMTP email alerts to be generated. 3.1.11. The smtp Group The SMTP group contains attributes to control the reporting of P2P management information via email. 3.1.12. The snmpControl Group The SNMP Control group contains attributes to control the management interface, especially the generation of traps (notifications). NB: Some attributes in this group hold their new settings in memory, which will only take effect after a system reboot. 3.1.13. The sntp Group The SNTP group contains attributes to control and monitor time synchronization. 3.1.14. The reset Group This mandatory group contains the objects which are applicable the PTP units reset information. 3.1.15. The versions Group This mandatory group contains the objects which are applicable the PTP units version information. 3.1.16. The pubStats Group This group contains the objects which are applicable the PTP units operational statistics. 3.1.17. The encryption Group The Encryption group contains objects to manage encryption over the wireless link. 3.1.18. The tDDControl Group 3.1.19. The aAAControl Group The AAA Control group contains objects specifically for Authentication, Authorization and Accounting. 3.1.20. The syslogControl Group 3.1.21. The routerProtocols Group 3.1.22. The cableDiagnostics Group 3.1.23. The supplementary Group 3.2. Textual Conventions The datatypes, MacAddress, BridgeId and Timeout, are used as textual conventions in this document. These textual conventions have NO effect on either the syntax nor the semantics of any managed object. Objects defined using these conventions are always encoded by means of the rules that define their primitive type. Hence, no changes to the SMI or the SNMP are necessary to accommodate these textual conventions which are adopted merely for the convenience of readers. 4. Definitions CAMBIUM-PTP650-MIB DEFINITIONS ::= BEGIN IMPORTS IpAddress, enterprises FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215 InetAddress, InetAddressType FROM INET-ADDRESS-MIB; -- Define the Cambium PTP object identifier cambium OBJECT IDENTIFIER ::= { enterprises 17713 } -- Groups in cambium ptp OBJECT IDENTIFIER ::= { cambium 1 } ptmp OBJECT IDENTIFIER ::= { cambium 2 } ptp650 OBJECT IDENTIFIER ::= { cambium 7 } -- Groups in ptp650 dfs OBJECT IDENTIFIER ::= { ptp650 3 } bridge OBJECT IDENTIFIER ::= { ptp650 4 } configuration OBJECT IDENTIFIER ::= { ptp650 5 } ethernet OBJECT IDENTIFIER ::= { ptp650 6 } tDM OBJECT IDENTIFIER ::= { ptp650 7 } license OBJECT IDENTIFIER ::= { ptp650 8 } management OBJECT IDENTIFIER ::= { ptp650 9 } phyControl OBJECT IDENTIFIER ::= { ptp650 10 } phyStatus OBJECT IDENTIFIER ::= { ptp650 12 } alarms OBJECT IDENTIFIER ::= { ptp650 13 } smtp OBJECT IDENTIFIER ::= { ptp650 15 } snmpControl OBJECT IDENTIFIER ::= { ptp650 16 } sntp OBJECT IDENTIFIER ::= { ptp650 17 } reset OBJECT IDENTIFIER ::= { ptp650 18 } versions OBJECT IDENTIFIER ::= { ptp650 19 } pubStats OBJECT IDENTIFIER ::= { ptp650 20 } encryption OBJECT IDENTIFIER ::= { ptp650 22 } tDDControl OBJECT IDENTIFIER ::= { ptp650 23 } aAAControl OBJECT IDENTIFIER ::= { ptp650 25 } syslogControl OBJECT IDENTIFIER ::= { ptp650 24 } routerProtocols OBJECT IDENTIFIER ::= { ptp650 26 } cableDiagnostics OBJECT IDENTIFIER ::= { ptp650 27 } supplementary OBJECT IDENTIFIER ::= { ptp650 96 } ptpTraps OBJECT IDENTIFIER ::= { ptp650 99 } ptpTrapPrefix OBJECT IDENTIFIER ::= { ptpTraps 0 } DfsTableEntry ::= SEQUENCE { dfsTableIndex INTEGER , dfsMeans INTEGER , dfsNineNinePointNinePercentiles INTEGER , dfsPeaks INTEGER } dfsTable OBJECT-TYPE SYNTAX SEQUENCE OF DfsTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " A table storing a snapshot of various DFS measurements for each channel" ::= { dfs 2 } dfsTableEntry OBJECT-TYPE SYNTAX DfsTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table DfsTable" INDEX { dfsTableIndex } ::= { dfsTable 1 } EthernetPriorityTableEntry ::= SEQUENCE { ethernetPriorityTableIndex INTEGER , ethernetPriorityQueueMapping INTEGER } ethernetPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF EthernetPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority." ::= { ethernet 15 } ethernetPriorityTableEntry OBJECT-TYPE SYNTAX EthernetPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table EthernetPriorityTable" INDEX { ethernetPriorityTableIndex } ::= { ethernetPriorityTable 1 } L2CPPriorityTableEntry ::= SEQUENCE { l2CPPriorityTableIndex INTEGER , l2CPPriorityQueueMapping INTEGER } l2CPPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF L2CPPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " A priority queue mapping table. This is a list of packet queues indexed by L2CP priority." ::= { ethernet 17 } l2CPPriorityTableEntry OBJECT-TYPE SYNTAX L2CPPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table L2CPPriorityTable" INDEX { l2CPPriorityTableIndex } ::= { l2CPPriorityTable 1 } IPDSCPPriorityTableEntry ::= SEQUENCE { iPDSCPPriorityTableIndex INTEGER , iPDSCPPriorityQueueMapping INTEGER } iPDSCPPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF IPDSCPPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority." ::= { ethernet 19 } iPDSCPPriorityTableEntry OBJECT-TYPE SYNTAX IPDSCPPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table IPDSCPPriorityTable" INDEX { iPDSCPPriorityTableIndex } ::= { iPDSCPPriorityTable 1 } MPLSTCPriorityTableEntry ::= SEQUENCE { mPLSTCPriorityTableIndex INTEGER , mPLSTCPriorityQueueMapping INTEGER } mPLSTCPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF MPLSTCPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority." ::= { ethernet 21 } mPLSTCPriorityTableEntry OBJECT-TYPE SYNTAX MPLSTCPriorityTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table MPLSTCPriorityTable" INDEX { mPLSTCPriorityTableIndex } ::= { mPLSTCPriorityTable 1 } TdmTableEntry ::= SEQUENCE { tdmTableIndex INTEGER , tDMChannelStatus INTEGER , tDMChannelLineCode INTEGER , tDMChannelCableLength INTEGER , tDMChannelLoopback INTEGER } tdmTable OBJECT-TYPE SYNTAX SEQUENCE OF TdmTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " A table storing a configuration and status for each TDM channel" ::= { tDM 5 } tdmTableEntry OBJECT-TYPE SYNTAX TdmTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table TdmTable" INDEX { tdmTableIndex } ::= { tdmTable 1 } LicenseRegulatoryBandsTableEntry ::= SEQUENCE { licenseRegulatoryBandsTableIndex INTEGER , licenseRegulatoryBandsList INTEGER } licenseRegulatoryBandsTable OBJECT-TYPE SYNTAX SEQUENCE OF LicenseRegulatoryBandsTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { license 18 } licenseRegulatoryBandsTableEntry OBJECT-TYPE SYNTAX LicenseRegulatoryBandsTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table LicenseRegulatoryBandsTable" INDEX { licenseRegulatoryBandsTableIndex } ::= { licenseRegulatoryBandsTable 1 } SNMPTrapTableEntry ::= SEQUENCE { sNMPTrapTableIndex INTEGER , sNMPTrapPortNumber INTEGER , sNMPTrapInternetAddressType INTEGER , sNMPTrapInternetAddress InetAddress , sNMPTrapReceiverEnabled INTEGER } sNMPTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF SNMPTrapTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " SNMP trap configuration table." ::= { snmpControl 4 } sNMPTrapTableEntry OBJECT-TYPE SYNTAX SNMPTrapTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table SNMPTrapTable" INDEX { sNMPTrapTableIndex } ::= { sNMPTrapTable 1 } SNTPServerTableEntry ::= SEQUENCE { sNTPServerTableIndex INTEGER , sNTPServerPortNumber INTEGER , sNTPServerStatus DisplayString , sNTPServerInternetAddressType INTEGER , sNTPServerInternetAddress InetAddress } sNTPServerTable OBJECT-TYPE SYNTAX SEQUENCE OF SNTPServerTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { sntp 15 } sNTPServerTableEntry OBJECT-TYPE SYNTAX SNTPServerTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table SNTPServerTable" INDEX { sNTPServerTableIndex } ::= { sNTPServerTable 1 } UserTableEntry ::= SEQUENCE { userTableIndex INTEGER , userName DisplayString , userRole INTEGER , userEnabled INTEGER , userPassword DisplayString } userTable OBJECT-TYPE SYNTAX SEQUENCE OF UserTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " The User Table Control group contains objects specifically for user account management." ::= { aAAControl 2 } userTableEntry OBJECT-TYPE SYNTAX UserTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table UserTable" INDEX { userTableIndex } ::= { userTable 1 } CableDiagnosticsResultTableEntry ::= SEQUENCE { cableDiagnosticsResultTableIndex INTEGER , cableDiagnosticsResultsDateTime INTEGER , cableDiagPair1Results INTEGER , cableDiagPair1Distance INTEGER , cableDiagPair2Results INTEGER , cableDiagPair2Distance INTEGER , cableDiagPair3Results INTEGER , cableDiagPair3Distance INTEGER , cableDiagPair4Results INTEGER , cableDiagPair4Distance INTEGER } cableDiagnosticsResultTable OBJECT-TYPE SYNTAX SEQUENCE OF CableDiagnosticsResultTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { cableDiagnostics 5 } cableDiagnosticsResultTableEntry OBJECT-TYPE SYNTAX CableDiagnosticsResultTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table CableDiagnosticsResultTable" INDEX { cableDiagnosticsResultTableIndex } ::= { cableDiagnosticsResultTable 1 } -- Dfs group attribute definitions -- dfsTableNumber OBJECT-TYPE SYNTAX INTEGER (1..63) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the dfsTable" ::= { dfs 1 } extendedSpectrumScanning OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Enables Extended Spectrum Scanning" ::= { dfs 3 } -- DfsTable group attribute definitions -- dfsTableIndex OBJECT-TYPE SYNTAX INTEGER (1..63) ACCESS not-accessible STATUS mandatory DESCRIPTION "used to index values in the dfsTable." ::= { dfsTableEntry 1 } dfsMeans OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Snapshot of DFS means" ::= { dfsTableEntry 2 } dfsNineNinePointNinePercentiles OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Snapshot of DFS 99.9 percentiles" ::= { dfsTableEntry 3 } dfsPeaks OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Snapshot of DFS peaks" ::= { dfsTableEntry 4 } -- Bridge group attribute definitions -- localPacketFiltering OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "When Local Packet Filtering is Enabled, the unit keeps track of the port (Main, SFP, Aux or Wireless) on which a packet with a given MAC source address destined to the management agent has been received. This MAC address to port mapping is then used in order to route any response from the management agent to the right port. When Local Packet Filtering is Disabled, any Ethernet packet from the management agent is sent to all ports." ::= { bridge 1 } -- Configuration group attribute definitions -- iPv4Address OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Internet protocol (IPv4) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network." ::= { configuration 1 } subnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance." ::= { configuration 2 } gatewayIPAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IPv4 address of a device on the current network that acts as an IPv4 network gateway. A gateway acts as an entrance / exit to packets from / to other networks" ::= { configuration 3 } targetMACAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS mandatory DESCRIPTION "MAC address of the PTP wireless unit forming the other end of the PTP link" ::= { configuration 4 } masterSlaveMode OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The PTP wireless link operates using a master and slave relationship" ::= { configuration 5 } maximumTransmitPower OBJECT-TYPE SYNTAX INTEGER (-15..30) ACCESS read-only STATUS mandatory DESCRIPTION "Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link. This may be reduced during installation" ::= { configuration 6 } antennaGain OBJECT-TYPE SYNTAX INTEGER (130..610) ACCESS read-write STATUS mandatory DESCRIPTION "Antenna Gain. Expressed in 10ths of dBi." ::= { configuration 7 } cableLoss OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna." ::= { configuration 8 } eIRP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm" ::= { configuration 9 } channelBandwidth OBJECT-TYPE SYNTAX INTEGER { bw-30-mhz(0), bw-15-mhz(1), bw-10-mhz(2), bw-5-mhz(3), bw-20-mhz(4), bw-56-mhz(5), bw-50-mhz(6), bw-40-mhz(7), bw-45-mhz(8) } ACCESS read-only STATUS mandatory DESCRIPTION "This control sets the bandwidth of the transmit and receive radio channels" ::= { configuration 11 } linkName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link." ::= { configuration 14 } siteName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "This field contains a user-provided description of the site name together with any additional notes" ::= { configuration 15 } accessMethod OBJECT-TYPE SYNTAX INTEGER { link-access(0), link-name-access(1), group-access(2) } ACCESS read-only STATUS mandatory DESCRIPTION "ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID." ::= { configuration 16 } groupID OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group" ::= { configuration 17 } iPv6Address OBJECT-TYPE SYNTAX DisplayString (SIZE(0..39)) ACCESS read-write STATUS mandatory DESCRIPTION "Internet protocol (IPv6) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network." ::= { configuration 18 } iPVersion OBJECT-TYPE SYNTAX INTEGER { ipv4(0), ipv6(1), dual-ipv4-and-ipv6(2) } ACCESS read-write STATUS mandatory DESCRIPTION "IP protocol selection. Choice of IPv4, IPv6 or Dual." ::= { configuration 20 } iPv6AutoConfiguredLinkLocalAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..39)) ACCESS read-only STATUS mandatory DESCRIPTION "The auto configured link local IPv6 address" ::= { configuration 21 } iPv6PrefixLength OBJECT-TYPE SYNTAX INTEGER (0..128) ACCESS read-write STATUS mandatory DESCRIPTION "IPv6 prefix length" ::= { configuration 22 } iPv6GatewayAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..39)) ACCESS read-write STATUS mandatory DESCRIPTION "The IPv6 address of a device on the current network that is currently acting as an IPv6 network gateway. A gateway acts as an entrance / exit to packets from / to other networks." ::= { configuration 23 } remoteInternetAddressType OBJECT-TYPE SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown-6(5), unknown-7(6), unknown-8(7), unknown-9(8), unknown-10(9), unknown-11(10), unknown-12(11), unknown-13(12), unknown-14(13), unknown-15(14), unknown-16(15), dns(16) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of Internet address specified by the associated remoteInternetAddressType." ::= { configuration 24 } remoteInternetAddress OBJECT-TYPE SYNTAX InetAddress ACCESS read-only STATUS mandatory DESCRIPTION "INET address used to identify the peer wireless unit" ::= { configuration 25 } subbandLowestFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Lowest center frequency of the subset of channels." ::= { configuration 26 } subbandHighestFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Highest center frequency of the subset of channels." ::= { configuration 27 } enableTransmission OBJECT-TYPE SYNTAX INTEGER { enabled(0), muted(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Control for enabling/disabling the radio transmitter of the Master. Note: Use Web Properties to control this feature." ::= { configuration 28 } -- Ethernet group attribute definitions -- mainPSUPortAutoNegotiation OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot." ::= { ethernet 1 } mainPSUPortAutoNegAdvertisement OBJECT-TYPE SYNTAX BITS { neg-invalid(2), neg-10-mbps-half-duplex(3), neg-10-mbps-full-duplex(4), neg-100-mbps-half-duplex(5), neg-100-mbps-full-duplex(6), neg-1000-mbps-full-duplex(7) } ACCESS read-only STATUS mandatory DESCRIPTION "This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!" ::= { ethernet 2 } mainPSUPortAutoMdix OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot" ::= { ethernet 3 } mainPSUPortStatus OBJECT-TYPE SYNTAX INTEGER { down(0), copper-link-up(1), fiber-link-up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= { ethernet 4 } mainPSUPortSpeedAndDuplex OBJECT-TYPE SYNTAX INTEGER { speed-1000-mbps-full-duplex(0), speed-100-mbps-full-duplex(1), speed-100-mbps-half-duplex(2), speed-10-mbps-full-duplex(3), speed-10-mbps-half-duplex(4), speed-unknown-6(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The current speed and duplex of the Main PSU Ethernet link" ::= { ethernet 5 } dataPortWirelessDownAlert OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem." ::= { ethernet 6 } useVLANForManagementInterfaces OBJECT-TYPE SYNTAX INTEGER { no-vlan-tagging(0), ieee-8021q-tagged-c-tag-type-8100(1), ieee-8021ad-tagged-s-tag-or-b-tag-type-88a8(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot" ::= { ethernet 7 } vLANManagementPriority OBJECT-TYPE SYNTAX INTEGER { p0(0), p1(1), p2(2), p3(3), p4(4), p5(5), p6(6), p7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This VLAN Priority (0-7) will be included in packets generated by the management interfaces" ::= { ethernet 8 } vLANManagementVID OBJECT-TYPE SYNTAX INTEGER (0..4094) ACCESS read-write STATUS mandatory DESCRIPTION "This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot" ::= { ethernet 11 } auxPortStatus OBJECT-TYPE SYNTAX INTEGER { down(0), copper-link-up(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= { ethernet 12 } auxPortSpeedAndDuplex OBJECT-TYPE SYNTAX INTEGER { speed-1000-mbps-full-duplex(0), speed-100-mbps-full-duplex(1), speed-100-mbps-half-duplex(2), speed-10-mbps-full-duplex(3), speed-10-mbps-half-duplex(4), speed-unknown-6(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The current speed and duplex of the Aux Ethernet link" ::= { ethernet 13 } ethernetPriorityTableNumber OBJECT-TYPE SYNTAX INTEGER (9) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the vLANPriorityTable." ::= { ethernet 14 } l2CPPriorityTableNumber OBJECT-TYPE SYNTAX INTEGER (5) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the l2CPPriorityTable." ::= { ethernet 16 } iPDSCPPriorityTableNumber OBJECT-TYPE SYNTAX INTEGER (64) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the iPDSCPPriorityTable." ::= { ethernet 18 } mPLSTCPriorityTableNumber OBJECT-TYPE SYNTAX INTEGER (8) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the mPLSTCPriorityTable." ::= { ethernet 20 } managementPortWirelessDownAlert OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem." ::= { ethernet 23 } qOSPriorityScheme OBJECT-TYPE SYNTAX INTEGER { ethernet(0), ipmpls(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLS" ::= { ethernet 24 } unknownNetworkPriorityQueueMapping OBJECT-TYPE SYNTAX INTEGER { q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS" ::= { ethernet 25 } dSCPManagementPriority OBJECT-TYPE SYNTAX INTEGER (0..63) ACCESS read-only STATUS mandatory DESCRIPTION "This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces" ::= { ethernet 26 } dataBridgingStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of Ethernet Data traffic bridging over the wireless link" ::= { ethernet 27 } mainPSUPortAllocation OBJECT-TYPE SYNTAX INTEGER { disabled(0), data-only(1), data-and-in-band-management(2), out-of-band-local-management(3), out-of-band-remote-management(4), second-data-only(5), second-data-and-in-band-management(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the service or services supported by the Main PSU Ethernet port" ::= { ethernet 28 } auxPortAllocation OBJECT-TYPE SYNTAX INTEGER { disabled(0), data-only(1), data-and-in-band-management(2), out-of-band-local-management(3), out-of-band-remote-management(4), second-data-only(5), second-data-and-in-band-management(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the service or services supported by the Aux Ethernet port" ::= { ethernet 29 } sFPPortAllocation OBJECT-TYPE SYNTAX INTEGER { disabled(0), data-only(1), data-and-in-band-management(2), out-of-band-local-management(3), out-of-band-remote-management(4), second-data-only(5), second-data-and-in-band-management(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the service or services supported by the SFP Ethernet port" ::= { ethernet 30 } dataPortPauseFrames OBJECT-TYPE SYNTAX INTEGER { tunnel(0), discard(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Controls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Data Port. Such frames are identified by the destination MAC Address being equal to 01-80-C2-00-00-01" ::= { ethernet 31 } sFPPortAutoNegotiation OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This controls whether the local SFP Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot." ::= { ethernet 32 } sFPPortAutoNegAdvertisement OBJECT-TYPE SYNTAX BITS { neg-invalid(2), neg-10-mbps-half-duplex(3), neg-10-mbps-full-duplex(4), neg-100-mbps-half-duplex(5), neg-100-mbps-full-duplex(6), neg-1000-mbps-full-duplex(7) } ACCESS read-only STATUS mandatory DESCRIPTION "This sets the different SFP Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!" ::= { ethernet 33 } sFPPortAutoMdix OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot" ::= { ethernet 34 } sFPPortStatus OBJECT-TYPE SYNTAX INTEGER { down(0), copper-link-up(1), fiber-link-up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= { ethernet 35 } sFPPortSpeedAndDuplex OBJECT-TYPE SYNTAX INTEGER { speed-1000-mbps-full-duplex(0), speed-100-mbps-full-duplex(1), speed-100-mbps-half-duplex(2), speed-10-mbps-full-duplex(3), speed-10-mbps-half-duplex(4), speed-unknown-6(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The current speed and duplex of the SFP Ethernet link" ::= { ethernet 36 } auxPortPowerOverEthernetOutput OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the Power Over Ethernet (PoE) output of the Aux port. Enabling PoE output may lead to system instability; please refer to the User Guide before enabling this control" ::= { ethernet 37 } auxPortPowerOverEthernetOutputStatus OBJECT-TYPE SYNTAX INTEGER { poe-output-on(0), poe-output-disabled(1), poe-output-enabled-but-not-active-error-or-no-load-present(2), poe-output-overload-error(3), poe-output-over-temp-error(4), poe-output-error-detected(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the Power Over Ethernet (PoE) output of the Aux port" ::= { ethernet 38 } syncETracking OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1), internal-tdm-use-only(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls whether Synchronous Ethernet (SyncE) network synchronization is enabled." ::= { ethernet 39 } syncEEquipmentClock OBJECT-TYPE SYNTAX INTEGER { eec-option-1(0), eec-option-2(1) } ACCESS read-write STATUS mandatory DESCRIPTION "EEC-Option 1 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 2048-kbit/s hierarchy. Corresponds to ITU-T G.813 Option 1; EEC-Option 2 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 1544-kbit/s hierarchy. Corresponds to Type IV clock from ITU-T G.812." ::= { ethernet 40 } mainPSUPortQLRxOverwrite OBJECT-TYPE SYNTAX INTEGER { disabled(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12) } ACCESS read-write STATUS mandatory DESCRIPTION "Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the main PSU port." ::= { ethernet 41 } mainPSUPortSSMTx OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Main PSU port" ::= { ethernet 42 } sFPPortSSMTx OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the SFP port" ::= { ethernet 43 } auxPortSSMTx OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Aux port" ::= { ethernet 44 } syncETrackingState OBJECT-TYPE SYNTAX INTEGER { disabled(0), acquiring-wireless-lock(1), free-running(2), locked-local-acquiring-holdover(3), locked-local-holdover-acquired(4), holdover(5), locked-remote-acquiring-holdover(6), locked-remote-holdover-acquired(7) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of Synchronous Ethernet (SyncE) network synchronization." ::= { ethernet 45 } mainPSUPortQLRx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12), ql-failed(13) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the main PSU port." ::= { ethernet 46 } auxPortQLRx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12), ql-failed(13) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the auxiliary port." ::= { ethernet 47 } sFPPortQLRx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12), ql-failed(13) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the SFP port." ::= { ethernet 48 } mainPSUPortQLTx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the main PSU port." ::= { ethernet 49 } auxPortQLTx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the auxiliary port." ::= { ethernet 50 } sFPPortQLTx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the SFP port." ::= { ethernet 51 } mainPSUPortSyncEMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The main PSU port Synchronous Ethernet (SyncE) Master/Slave status" ::= { ethernet 52 } auxPortSyncEMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The auxiliary port Synchronous Ethernet (SyncE) Master/Slave status" ::= { ethernet 53 } sFPPortSyncEMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The SFP port Synchronous Ethernet (SyncE) Master/Slave status" ::= { ethernet 54 } mainPSUPortGigabitMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1), not-applicable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The main PSU port Gigabit Ethernet Master/Slave status" ::= { ethernet 55 } auxPortGigabitMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1), not-applicable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The auxiliary port Gigabit Ethernet Master/Slave status" ::= { ethernet 56 } sFPPortGigabitMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1), not-applicable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The SFP port Gigabit Ethernet Master/Slave status" ::= { ethernet 57 } transparentClock OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This control enables the Precision Time Protocol (IEEE-1588) Transparent Clock. Once enabled the unit will modify the correction field in PTP event messages to take account of the time these frames have been resident in this system. This will happen for all PTP frames at Layer 2 & Layer 3 (IPv4 & IPv6) unless a transparent clock VLAN is enabled." ::= { ethernet 58 } transparentClockVLAN OBJECT-TYPE SYNTAX INTEGER { all(0), s-tagged(1), c-tagged(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If All is selected then all PTP frames will have their correction fields modified with the residence time. If an S-TAG or C-TAG is selected, only frames with this VLAN tag and matching the VLAN ID in the Transparent Clock VID will have their correction fields modified." ::= { ethernet 59 } transparentClockVID OBJECT-TYPE SYNTAX INTEGER (0..4094) ACCESS read-write STATUS mandatory DESCRIPTION "The VLAN ID which frames must match if they are to be corrected. Only valid when an S-TAG or C-TAG has been selected." ::= { ethernet 60 } mainPSUPortAcceptedQLRx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12), ql-failed(13) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the main PSU port." ::= { ethernet 61 } auxPortAcceptedQLRx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12), ql-failed(13) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the auxiliary port." ::= { ethernet 62 } sFPPortAcceptedQLRx OBJECT-TYPE SYNTAX INTEGER { none(0), ql-prs(1), ql-stu(2), ql-prc(3), ql-st2(4), ql-ssu-a-ql-tnc(5), ql-ssu-b(6), ql-st3e(7), ql-eec2-ql-st3(8), ql-eec1-ql-sec(9), ql-smc(10), ql-prov(11), ql-dnu-ql-dus(12), ql-failed(13) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the SFP port." ::= { ethernet 63 } mainPSUPortSyncERxStatus OBJECT-TYPE SYNTAX INTEGER { good(0), wait-to-restore(1), failed(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Receive Status of the main PSU port" ::= { ethernet 64 } auxPortSyncERxStatus OBJECT-TYPE SYNTAX INTEGER { good(0), wait-to-restore(1), failed(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Receive Status of the auxiliary port" ::= { ethernet 65 } sFPPortSyncERxStatus OBJECT-TYPE SYNTAX INTEGER { good(0), wait-to-restore(1), failed(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The Synchronous Ethernet (SyncE) Receive Status of the SFP port" ::= { ethernet 66 } nIDULanPortStatus OBJECT-TYPE SYNTAX INTEGER { down(0), copper-link-up(1), fiber-link-up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= { ethernet 67 } nIDULanPortSpeedAndDuplex OBJECT-TYPE SYNTAX INTEGER { speed-1000-mbps-full-duplex(0), speed-100-mbps-full-duplex(1), speed-100-mbps-half-duplex(2), speed-10-mbps-full-duplex(3), speed-10-mbps-half-duplex(4), speed-unknown-6(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The current speed and duplex of the Ethernet link to the NIDU LAN Port" ::= { ethernet 68 } oOBPriorityQueueMapping OBJECT-TYPE SYNTAX INTEGER { q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Configures the classification of traffic to an egress queue at the wireless port" ::= { ethernet 69 } nIDULanPortAutoNegotiation OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot." ::= { ethernet 70 } nIDULanPortAutoNegAdvertisement OBJECT-TYPE SYNTAX BITS { neg-invalid(2), neg-10-mbps-half-duplex(3), neg-10-mbps-full-duplex(4), neg-100-mbps-half-duplex(5), neg-100-mbps-full-duplex(6), neg-1000-mbps-full-duplex(7) } ACCESS read-only STATUS mandatory DESCRIPTION "This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!" ::= { ethernet 71 } nIDULanPortAutoMdix OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot" ::= { ethernet 72 } nIDULanPortGigabitMasterSlaveStatus OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1), not-applicable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The NIDU LAN port Gigabit Ethernet Master/Slave status" ::= { ethernet 73 } txMABFrames OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of MAB frames transmitted" ::= { ethernet 74 } managementNetworkAccessEnabled OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } ACCESS read-write STATUS mandatory DESCRIPTION "When enabled the local Out-of-Band interface can be used to access the remote management network. If not enabled the local management agent can still be accessed from the remote management network and the local Out-of-Band interface" ::= { ethernet 75 } secondDataPortPauseFrames OBJECT-TYPE SYNTAX INTEGER { tunnel(0), discard(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Controls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Second Data Service Port. Such frames are identified by the destination MAC Address being equal to 01-80-C2-00-00-01" ::= { ethernet 76 } secondDataBridgingStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of bridging Second Data Service Ethernet traffic over the wireless link" ::= { ethernet 80 } transparentClockPort OBJECT-TYPE SYNTAX INTEGER { main-psu(0), aux(1), sfp(2) } ACCESS read-write STATUS mandatory DESCRIPTION "IEEE 1588 Transparent Clock source" ::= { ethernet 81 } -- EthernetPriorityTable group attribute definitions -- ethernetPriorityTableIndex OBJECT-TYPE SYNTAX INTEGER { p0(1), p1(2), p2(3), p3(4), p4(5), p5(6), p6(7), p7(8), untagged(9) } ACCESS not-accessible STATUS mandatory DESCRIPTION "Ethernet priority flag, used to index values in the ethernetPriorityTable" ::= { ethernetPriorityTableEntry 1 } ethernetPriorityQueueMapping OBJECT-TYPE SYNTAX INTEGER { q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port" ::= { ethernetPriorityTableEntry 2 } -- L2CPPriorityTable group attribute definitions -- l2CPPriorityTableIndex OBJECT-TYPE SYNTAX INTEGER { bridge(1), mrp(2), cfm(3), r-aps(4), eaps(5) } ACCESS not-accessible STATUS mandatory DESCRIPTION "L2CP priority flag, used to index values in the l2CPPriorityTable" ::= { l2CPPriorityTableEntry 1 } l2CPPriorityQueueMapping OBJECT-TYPE SYNTAX INTEGER { q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port" ::= { l2CPPriorityTableEntry 2 } -- IPDSCPPriorityTable group attribute definitions -- iPDSCPPriorityTableIndex OBJECT-TYPE SYNTAX INTEGER (1..64) ACCESS not-accessible STATUS mandatory DESCRIPTION "IP DSCP priority flag, used to index values in the iPDSCPPriorityTable" ::= { iPDSCPPriorityTableEntry 1 } iPDSCPPriorityQueueMapping OBJECT-TYPE SYNTAX INTEGER { q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port" ::= { iPDSCPPriorityTableEntry 2 } -- MPLSTCPriorityTable group attribute definitions -- mPLSTCPriorityTableIndex OBJECT-TYPE SYNTAX INTEGER (1..8) ACCESS not-accessible STATUS mandatory DESCRIPTION "MPLS TC priority flag, used to index values in the mPLSTCPriorityTable" ::= { mPLSTCPriorityTableEntry 1 } mPLSTCPriorityQueueMapping OBJECT-TYPE SYNTAX INTEGER { q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port" ::= { mPLSTCPriorityTableEntry 2 } -- TDM group attribute definitions -- tDMInterfaceControl OBJECT-TYPE SYNTAX INTEGER { none(0), e1(1), t1(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The line interface type. If this is set to 'None' then the TDM interfaces are disabled, and the TDM settings will be ignored." ::= { tDM 1 } tDMInterfaceStatus OBJECT-TYPE SYNTAX INTEGER { ok(0), connected-not-configured(1), not-connected(2), nidu-detected-on-aux-port(3), error(4), code-download-in-progress(5) } ACCESS read-only STATUS mandatory DESCRIPTION "@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used" ::= { tDM 2 } tDMEnabledChannels OBJECT-TYPE SYNTAX INTEGER (0..8) ACCESS read-only STATUS mandatory DESCRIPTION "The number of TDM channels enabled in the system" ::= { tDM 3 } tdmTableNumber OBJECT-TYPE SYNTAX INTEGER (1..8) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the TdmTable" ::= { tDM 4 } tDMConfigurationMismatch OBJECT-TYPE SYNTAX INTEGER { ok(0), line-type-mismatch(1), enabled-channels-mismatch(2), line-type-and-enabled-channels-mismatch(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end." ::= { tDM 6 } lowestTDMModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-acquisition(0), mod-bpsk-63-percent(1), mod-qpsk-63-percent-single(2), mod-transient-1(3), mod-qpsk-87-percent-single(4), mod-transient-2(5), mod-16qam-63-percent-single-a(6), mod-transient-3(7), mod-16qam-87-percent-single(8), mod-transient-4(9), mod-64qam-75-percent-single(10), mod-transient-5(11), mod-64qam-92-percent-single(12), mod-transient-6(13), mod-256qam-81-percent-single(14), mod-16qam-63-percent-single-b(15), mod-16qam-63-percent-dual(16), mod-transient-7(17), mod-16qam-87-percent-dual(18), mod-transient-8(19), mod-64qam-75-percent-dual(20), mod-transient-9(21), mod-64qam-92-percent-dual(22), mod-transient-10(23), mod-256qam-81-percent-dual(24) } ACCESS read-only STATUS mandatory DESCRIPTION "The lowest modulation mode at which tdm data will be sent. The effective lowest modulation mode is displayed in the TDM Configuration page" ::= { tDM 7 } -- TdmTable group attribute definitions -- tdmTableIndex OBJECT-TYPE SYNTAX INTEGER (1..8) ACCESS not-accessible STATUS mandatory DESCRIPTION "TDM Channel flag, used to index channels in the TdmTable" ::= { tdmTableEntry 1 } tDMChannelStatus OBJECT-TYPE SYNTAX INTEGER { up(0), no-signal-local(1), no-signal-remote(2), no-signal-local-and-remote(3), remote-timing(4), no-signal-local-and-remote-timing(5), disabled(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the TDM channels. A value of 0 indicates that a TDM channel is established" ::= { tdmTableEntry 2 } tDMChannelLineCode OBJECT-TYPE SYNTAX INTEGER { ami(0), b8zs-or-hdb3(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The line code setting of the TDM interfaces. This must match the setting of the device connected to an interface" ::= { tdmTableEntry 3 } tDMChannelCableLength OBJECT-TYPE SYNTAX INTEGER { feet-133(0), feet-266(1), feet-399(2), feet-533(3), feet-655(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The lengths of the cables connected to the TDM interfaces, measured in feet" ::= { tdmTableEntry 4 } tDMChannelLoopback OBJECT-TYPE SYNTAX INTEGER { none(0), copper(1), wireless(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= { tdmTableEntry 5 } -- License group attribute definitions -- regulatoryBand OBJECT-TYPE SYNTAX INTEGER { reg-invalid(0), reg-1-58-ghz(1), reg-2-58-ghz(2), reg-3-58-ghz(3), reg-4-58-ghz(4), reg-5-58-ghz(5), reg-6-58-ghz(6), reg-7-54-ghz-unrestricted-eirp-with-dfs(7), reg-8-54-ghz-unrestricted-eirp(8), reg-9(9), reg-10-58-ghz(10), reg-11-58-ghz(11), reg-12-54-ghz-fcc-u-nii-2c(12), reg-13-54-ghz(13), reg-14-49-ghz-public-safety(14), reg-15(15), reg-16-59-ghz(16), reg-17-59-ghz(17), reg-18-49-ghz-public-safety(18), reg-19-58-ghz(19), reg-20-54-ghz(20), reg-21-54-ghz(21), reg-22-58-ghz(22), reg-23(23), reg-24-58-ghz(24), reg-25-58-ghz-etsi(25), reg-26-54-ghz-etsi(26), reg-27-58-ghz(27), reg-28-58-ghz(28), reg-29-58-ghz-unrestricted-eirp-with-dfs-and-rttt(29), reg-30-54-ghz(30), reg-31-58-ghz(31), reg-32-49-ghz-licensed(32), reg-33-49-ghz-etsi-broadband-disaster-relief(33), reg-34-58-ghz(34), reg-35-58-ghz-unrestricted-eirp(35), reg-36-54-ghz(36), reg-37-58-ghz(37), reg-38-52-ghz-fcc-u-nii-2a(38), reg-39-51-ghz-etsi-broadband-disaster-relief(39), reg-40-54-ghz(40), reg-41-54-ghz(41), reg-42-54-ghz(42), reg-43-54-ghz(43), reg-44-58-ghz(44), reg-45-58-ghz(45), reg-46-58-ghz(46), reg-47-58-ghz(47), reg-48-58-ghz(48), reg-49-58-ghz(49), reg-50-58-ghz(50), reg-51-58-ghz(51), reg-52-58-ghz(52), reg-53-58-ghz(53), reg-54-58-ghz(54), reg-55-58-ghz(55), reg-56-54-ghz(56), reg-57-54-ghz(57), reg-58-58-ghz(58), reg-59-58-ghz(59), reg-60-58-ghz(60), reg-61-49-ghz(61), reg-62-52-ghz(62), reg-63-52-ghz(63), reg-64-51-ghz(64), reg-65-51-ghz(65), reg-66-51-ghz(66), reg-67-52-ghz(67), reg-68-52-ghz(68), reg-69-52-ghz(69), reg-70-52-ghz(70), reg-71-52-ghz(71), reg-72-52-ghz(72), reg-73-52-ghz(73), reg-74-52-ghz(74), reg-75-52-ghz(75), reg-76-52-ghz(76), reg-77-52-ghz(77), reg-78-49-ghz(78), reg-79-54-ghz(79), reg-80-49-ghz(80), reg-81-47-ghz(81), reg-82-47-ghz(82), reg-83-52-ghz(83), reg-84-51-ghz-fcc-u-nii-1(84), reg-85-52-ghz-fcc-u-nii-1-2a(85), reg-86-54-ghz-fcc-u-nii-2a-2c(86), reg-87-58-ghz(87), reg-88-49-ghz(88), reg-89-49-ghz(89), reg-90-54-ghz-fcc-u-nii-2c-parabolic-antenna(90), reg-91-52-ghz-fcc-u-nii-2a-parabolic-antenna(91), reg-92-51-ghz-fcc-u-nii-1-parabolic-antenna(92), reg-93-49-ghz(93), reg-94(94), reg-95(95), reg-96(96), reg-97(97), reg-98(98), reg-99(99), reg-100(100), reg-101(101), reg-102(102), reg-103(103), reg-104(104), reg-105(105), reg-106(106), reg-107(107), reg-108(108), reg-109(109), reg-110(110), reg-111(111), reg-112(112), reg-113(113), reg-114(114), reg-115(115), reg-116(116), reg-117(117), reg-118(118), reg-119(119), reg-120(120), reg-121(121), reg-122(122), reg-123(123), reg-124(124), reg-125(125), reg-126(126), reg-127(127), reg-128(128), reg-129(129), reg-130(130), reg-131(131), reg-132(132), reg-133(133), reg-134(134), reg-135(135), reg-136(136), reg-137(137), reg-138(138), reg-139(139), reg-140(140), reg-141(141), reg-142(142), reg-143(143), reg-144(144), reg-145(145), reg-146(146), reg-147(147), reg-148(148), reg-149(149), reg-150(150), reg-151(151), reg-152(152), reg-153(153), reg-154(154), reg-155(155), reg-156(156), reg-157(157), reg-158(158), reg-159(159), reg-160(160), reg-161(161), reg-162(162), reg-163(163), reg-164(164), reg-165(165), reg-166(166), reg-167(167), reg-168(168), reg-169(169), reg-170(170), reg-171(171), reg-172(172), reg-173(173), reg-174(174), reg-175(175), reg-176(176), reg-177(177), reg-178(178), reg-179(179), reg-180(180), reg-181(181), reg-182(182), reg-183(183), reg-184(184), reg-185(185), reg-186(186), reg-187(187), reg-188(188), reg-189(189), reg-190(190), reg-191(191), reg-192(192), reg-193(193), reg-194(194), reg-195(195), reg-196(196), reg-197(197), reg-198(198), reg-199(199), reg-200(200), reg-201(201), reg-202(202), reg-203(203), reg-204(204), reg-205(205), reg-206(206), reg-207(207), reg-208(208), reg-209(209), reg-210(210), reg-211(211), reg-212(212), reg-213(213), reg-214(214), reg-215(215), reg-216(216), reg-217(217), reg-218(218), reg-219(219), reg-220(220), reg-221(221), reg-222(222), reg-223(223), reg-224(224), reg-225(225), reg-226(226), reg-227(227), reg-228(228), reg-229(229), reg-230(230), reg-231(231), reg-232(232), reg-233(233), reg-234(234), reg-235(235), reg-236(236), reg-237(237), reg-238(238), reg-239(239), reg-240(240), reg-241(241), reg-242(242), reg-243(243), reg-244(244), reg-245(245), reg-246(246), reg-247(247), reg-248(248), reg-249(249), reg-250(250), reg-251(251), reg-252(252), reg-253(253), reg-254(254), reg-255(255) } ACCESS read-only STATUS mandatory DESCRIPTION "The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key. NB: a change of state may generate an SNMP trap and/or SMTP email alert." ::= { license 1 } productVariant OBJECT-TYPE SYNTAX INTEGER { ptp-xx400-full(0), ptp-xx400-deprecated-1(1), ptp-xx400-deprecated-2(2), ptp-xx400-lite(3), spare-1(4), ptp-xx300(5), spare-2(6), spare-3(7), ptp-xx500-full-deprecated(8), ptp-xx500-lite-deprecated(9), ptp-xx500(10), ptp-xx600-lite(11), ptp-xx600-full(12), ptp-xx650(13), spare-6(14), ptp-800(15) } ACCESS read-only STATUS mandatory DESCRIPTION "The product variant" ::= { license 2 } productName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-only STATUS mandatory DESCRIPTION "Name of the product variant" ::= { license 3 } frequencyVariant OBJECT-TYPE SYNTAX INTEGER { freq-5-ghz(0), freq-4-ghz(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The hardware frequency variant" ::= { license 5 } sNMPv3Enable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "SNMPv3 availability control" ::= { license 9 } licenseVersion OBJECT-TYPE SYNTAX INTEGER (1) ACCESS read-only STATUS mandatory DESCRIPTION "The license key version." ::= { license 12 } licenseUnitSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..11)) ACCESS read-only STATUS mandatory DESCRIPTION "The unit serial number." ::= { license 13 } licenseIssueNumber OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The license key issue number for this unit." ::= { license 15 } licenseCountry OBJECT-TYPE SYNTAX DisplayString (SIZE(0..103)) ACCESS read-only STATUS mandatory DESCRIPTION "The country in which this unit is licensed to operate." ::= { license 16 } licenseNumberOfRegulatoryBands OBJECT-TYPE SYNTAX INTEGER (0..32) ACCESS read-only STATUS mandatory DESCRIPTION "The number of regulatory bands for which the unit is licensed to operate." ::= { license 17 } licenseBandwidthCap OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The wireless link bandwidth cap in MHz. Zero indicates no bandwidth cap." ::= { license 20 } licenseEncryption OBJECT-TYPE SYNTAX INTEGER { none(0), aes-rijndael(1), aes-192-bit-rijndael(2), aes-256-bit-rijndael(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key encryption algorithms available." ::= { license 21 } licenseSecurityLevel OBJECT-TYPE SYNTAX INTEGER { normal(0), fips(1), uc-apl(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key security level." ::= { license 22 } licenseGroupAccess OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key group access setting." ::= { license 23 } licenseOOBManagementSupport OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key Out-Of-Band (OOB) support setting." ::= { license 24 } licenseSFPPortSupport OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key Ethernet SFP Port support setting." ::= { license 25 } licenseAuxiliaryPortSupport OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key Ethernet Auxiliary Port support setting." ::= { license 26 } licenseCapacity OBJECT-TYPE SYNTAX INTEGER { full(0), mid(1), lite(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key capacity" ::= { license 27 } licenseMaxNumberOfTDMChannels OBJECT-TYPE SYNTAX INTEGER (0..8) ACCESS read-only STATUS mandatory DESCRIPTION "The license key maximum TDM channels setting. Zero indicates TDM not available." ::= { license 28 } licenseIEEE1588Support OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key IEEE-1588 support setting." ::= { license 29 } licenseSyncESupport OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key SyncE support setting." ::= { license 30 } licenseIPv6Support OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key IPv6 support setting." ::= { license 31 } licenseMinimumFirmwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..23)) ACCESS read-only STATUS mandatory DESCRIPTION "The minimum firmware version required to support this license key." ::= { license 32 } licenseFullCapabilityTrialStatus OBJECT-TYPE SYNTAX INTEGER { available(0), active(1), inactive(2), expired(3), unavailable(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key full capability trial period status." ::= { license 33 } licenseRemainingTrialPeriod OBJECT-TYPE SYNTAX INTEGER (0..31536000) ACCESS read-only STATUS mandatory DESCRIPTION "The remaining time for the license key full capability trial period." ::= { license 34 } licenseRemainingTrialPeriodAlarm OBJECT-TYPE SYNTAX INTEGER { full-capability-trial-not-active-or-more-than-7-days-remaining(0), full-capability-trial-expiring-in-less-than-7-days(1), full-capability-trial-expiring-in-less-than-6-days(2), full-capability-trial-expiring-in-less-than-5-days(3), full-capability-trial-expiring-in-less-than-4-days(4), full-capability-trial-expiring-in-less-than-3-days(5), full-capability-trial-expiring-in-less-than-2-days(6), full-capability-trial-expiring-in-less-than-1-day(7), full-capability-trial-has-expired(8) } ACCESS read-only STATUS mandatory DESCRIPTION "If the full capability trial license period is about to expire then purchase a license upgrade from your reseller." ::= { license 35 } capacityVariantMismatch OBJECT-TYPE SYNTAX INTEGER { no-error(0), mismatch-detected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity." ::= { license 36 } licenseTDDSyncSupport OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key TDD Synchronization support setting." ::= { license 37 } licenseMaxLinkRange OBJECT-TYPE SYNTAX INTEGER (0..1999) ACCESS read-only STATUS mandatory DESCRIPTION "Maximum licensed range for the wireless link in tenths of km. A value of zero indicates that the maximum link range is not limited by the license." ::= { license 38 } licenseTrialPeriod OBJECT-TYPE SYNTAX INTEGER (0..365) ACCESS read-only STATUS mandatory DESCRIPTION "The license key maximum trial period, in days." ::= { license 39 } licenseRARSupport OBJECT-TYPE SYNTAX INTEGER { disabled(0), mab(1), dlep(2), mab-and-dlep(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The license key Radio Aware Routing support setting." ::= { license 40 } -- LicenseRegulatoryBandsTable group attribute definitions -- licenseRegulatoryBandsTableIndex OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS not-accessible STATUS mandatory DESCRIPTION "License regulatory bands, used to index the LicenseRegulatoryBandsTable." ::= { licenseRegulatoryBandsTableEntry 1 } licenseRegulatoryBandsList OBJECT-TYPE SYNTAX INTEGER { reg-invalid(0), reg-1-58-ghz(1), reg-2-58-ghz(2), reg-3-58-ghz(3), reg-4-58-ghz(4), reg-5-58-ghz(5), reg-6-58-ghz(6), reg-7-54-ghz-unrestricted-eirp-with-dfs(7), reg-8-54-ghz-unrestricted-eirp(8), reg-9(9), reg-10-58-ghz(10), reg-11-58-ghz(11), reg-12-54-ghz-fcc-u-nii-2c(12), reg-13-54-ghz(13), reg-14-49-ghz-public-safety(14), reg-15(15), reg-16-59-ghz(16), reg-17-59-ghz(17), reg-18-49-ghz-public-safety(18), reg-19-58-ghz(19), reg-20-54-ghz(20), reg-21-54-ghz(21), reg-22-58-ghz(22), reg-23(23), reg-24-58-ghz(24), reg-25-58-ghz-etsi(25), reg-26-54-ghz-etsi(26), reg-27-58-ghz(27), reg-28-58-ghz(28), reg-29-58-ghz-unrestricted-eirp-with-dfs-and-rttt(29), reg-30-54-ghz(30), reg-31-58-ghz(31), reg-32-49-ghz-licensed(32), reg-33-49-ghz-etsi-broadband-disaster-relief(33), reg-34-58-ghz(34), reg-35-58-ghz-unrestricted-eirp(35), reg-36-54-ghz(36), reg-37-58-ghz(37), reg-38-52-ghz-fcc-u-nii-2a(38), reg-39-51-ghz-etsi-broadband-disaster-relief(39), reg-40-54-ghz(40), reg-41-54-ghz(41), reg-42-54-ghz(42), reg-43-54-ghz(43), reg-44-58-ghz(44), reg-45-58-ghz(45), reg-46-58-ghz(46), reg-47-58-ghz(47), reg-48-58-ghz(48), reg-49-58-ghz(49), reg-50-58-ghz(50), reg-51-58-ghz(51), reg-52-58-ghz(52), reg-53-58-ghz(53), reg-54-58-ghz(54), reg-55-58-ghz(55), reg-56-54-ghz(56), reg-57-54-ghz(57), reg-58-58-ghz(58), reg-59-58-ghz(59), reg-60-58-ghz(60), reg-61-49-ghz(61), reg-62-52-ghz(62), reg-63-52-ghz(63), reg-64-51-ghz(64), reg-65-51-ghz(65), reg-66-51-ghz(66), reg-67-52-ghz(67), reg-68-52-ghz(68), reg-69-52-ghz(69), reg-70-52-ghz(70), reg-71-52-ghz(71), reg-72-52-ghz(72), reg-73-52-ghz(73), reg-74-52-ghz(74), reg-75-52-ghz(75), reg-76-52-ghz(76), reg-77-52-ghz(77), reg-78-49-ghz(78), reg-79-54-ghz(79), reg-80-49-ghz(80), reg-81-47-ghz(81), reg-82-47-ghz(82), reg-83-52-ghz(83), reg-84-51-ghz-fcc-u-nii-1(84), reg-85-52-ghz-fcc-u-nii-1-2a(85), reg-86-54-ghz-fcc-u-nii-2a-2c(86), reg-87-58-ghz(87), reg-88-49-ghz(88), reg-89-49-ghz(89), reg-90-54-ghz-fcc-u-nii-2c-parabolic-antenna(90), reg-91-52-ghz-fcc-u-nii-2a-parabolic-antenna(91), reg-92-51-ghz-fcc-u-nii-1-parabolic-antenna(92), reg-93-49-ghz(93), reg-94(94), reg-95(95), reg-96(96), reg-97(97), reg-98(98), reg-99(99), reg-100(100), reg-101(101), reg-102(102), reg-103(103), reg-104(104), reg-105(105), reg-106(106), reg-107(107), reg-108(108), reg-109(109), reg-110(110), reg-111(111), reg-112(112), reg-113(113), reg-114(114), reg-115(115), reg-116(116), reg-117(117), reg-118(118), reg-119(119), reg-120(120), reg-121(121), reg-122(122), reg-123(123), reg-124(124), reg-125(125), reg-126(126), reg-127(127), reg-128(128), reg-129(129), reg-130(130), reg-131(131), reg-132(132), reg-133(133), reg-134(134), reg-135(135), reg-136(136), reg-137(137), reg-138(138), reg-139(139), reg-140(140), reg-141(141), reg-142(142), reg-143(143), reg-144(144), reg-145(145), reg-146(146), reg-147(147), reg-148(148), reg-149(149), reg-150(150), reg-151(151), reg-152(152), reg-153(153), reg-154(154), reg-155(155), reg-156(156), reg-157(157), reg-158(158), reg-159(159), reg-160(160), reg-161(161), reg-162(162), reg-163(163), reg-164(164), reg-165(165), reg-166(166), reg-167(167), reg-168(168), reg-169(169), reg-170(170), reg-171(171), reg-172(172), reg-173(173), reg-174(174), reg-175(175), reg-176(176), reg-177(177), reg-178(178), reg-179(179), reg-180(180), reg-181(181), reg-182(182), reg-183(183), reg-184(184), reg-185(185), reg-186(186), reg-187(187), reg-188(188), reg-189(189), reg-190(190), reg-191(191), reg-192(192), reg-193(193), reg-194(194), reg-195(195), reg-196(196), reg-197(197), reg-198(198), reg-199(199), reg-200(200), reg-201(201), reg-202(202), reg-203(203), reg-204(204), reg-205(205), reg-206(206), reg-207(207), reg-208(208), reg-209(209), reg-210(210), reg-211(211), reg-212(212), reg-213(213), reg-214(214), reg-215(215), reg-216(216), reg-217(217), reg-218(218), reg-219(219), reg-220(220), reg-221(221), reg-222(222), reg-223(223), reg-224(224), reg-225(225), reg-226(226), reg-227(227), reg-228(228), reg-229(229), reg-230(230), reg-231(231), reg-232(232), reg-233(233), reg-234(234), reg-235(235), reg-236(236), reg-237(237), reg-238(238), reg-239(239), reg-240(240), reg-241(241), reg-242(242), reg-243(243), reg-244(244), reg-245(245), reg-246(246), reg-247(247), reg-248(248), reg-249(249), reg-250(250), reg-251(251), reg-252(252), reg-253(253), reg-254(254), reg-255(255) } ACCESS read-only STATUS mandatory DESCRIPTION "The list of regulatory bands for which the unit is licensed to operate. A regulatory band prohibits the wireless unit from operating outside the regulated limits. An invalid regulatory band indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert." ::= { licenseRegulatoryBandsTableEntry 2 } -- Management group attribute definitions -- targetRange OBJECT-TYPE SYNTAX INTEGER (0..2000) ACCESS read-only STATUS mandatory DESCRIPTION "Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0" ::= { management 1 } rangingMode OBJECT-TYPE SYNTAX INTEGER { auto-0-to-40-km(0), auto-0-to-100-km(1), auto-0-to-200-km(2), target-range(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range" ::= { management 2 } installStatus OBJECT-TYPE SYNTAX INTEGER { ok(0), wrong-peer(1) } ACCESS read-only STATUS mandatory DESCRIPTION "A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert" ::= { management 3 } installArmState OBJECT-TYPE SYNTAX INTEGER { disarmed(0), armed(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= { management 4 } tFTPServerPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved" ::= { management 6 } tFTPSoftwareUpgradeFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) ACCESS read-write STATUS mandatory DESCRIPTION "Filename of the Software Upgrade to be loaded from the TFTP Server" ::= { management 7 } tFTPStartSoftwareUpgrade OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (DSO) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a regulatory band where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebooted" ::= { management 8 } tFTPSoftwareUpgradeStatus OBJECT-TYPE SYNTAX INTEGER { idle(0), upload-in-progress(1), upload-successful-programming-flash(2), upgrade-successful-reboot-to-run-the-new-software-image(3), upgrade-failed(4), upgrade-warning(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The current status of the TFTP Software upgrade process" ::= { management 9 } tFTPSoftwareUpgradeStatusText OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) ACCESS read-only STATUS mandatory DESCRIPTION "Descriptive text describing the status of the TFTP Software upgrade process, including any error details" ::= { management 10 } tFTPSoftwareUpgradeStatusAdditionalText OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) ACCESS read-only STATUS mandatory DESCRIPTION "Any additional text describing the status of the TFTP Software upgrade process, including any error details" ::= { management 11 } hTTPAccessEnabled OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)" ::= { management 12 } telnetAccessEnabled OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)" ::= { management 13 } hTTPPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)" ::= { management 14 } hTTPSPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)" ::= { management 15 } telnetPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)" ::= { management 16 } hTTPSAccessEnabled OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)" ::= { management 17 } tFTPServerInternetAddressType OBJECT-TYPE SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown-6(5), unknown-7(6), unknown-8(7), unknown-9(8), unknown-10(9), unknown-11(10), unknown-12(11), unknown-13(12), unknown-14(13), unknown-15(14), unknown-16(15), dns(16) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of Internet address specified by the associated tFTPServerInternetAddress." ::= { management 18 } tFTPServerInternetAddress OBJECT-TYPE SYNTAX InetAddress ACCESS read-write STATUS mandatory DESCRIPTION "INET address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved" ::= { management 19 } lowestDataModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-acquisition(0), mod-bpsk-63-percent(1), mod-qpsk-63-percent-single(2), mod-transient-1(3), mod-qpsk-87-percent-single(4), mod-transient-2(5), mod-16qam-63-percent-single-a(6), mod-transient-3(7), mod-16qam-87-percent-single(8), mod-transient-4(9), mod-64qam-75-percent-single(10), mod-transient-5(11), mod-64qam-92-percent-single(12), mod-transient-6(13), mod-256qam-81-percent-single(14), mod-16qam-63-percent-single-b(15), mod-16qam-63-percent-dual(16), mod-transient-7(17), mod-16qam-87-percent-dual(18), mod-transient-8(19), mod-64qam-75-percent-dual(20), mod-transient-9(21), mod-64qam-92-percent-dual(22), mod-transient-10(23), mod-256qam-81-percent-dual(24) } ACCESS read-only STATUS mandatory DESCRIPTION "The lowest modulation mode at which Ethernet Data traffic will be bridged over the wireless link" ::= { management 20 } lowestSecondDataModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-acquisition(0), mod-bpsk-63-percent(1), mod-qpsk-63-percent-single(2), mod-transient-1(3), mod-qpsk-87-percent-single(4), mod-transient-2(5), mod-16qam-63-percent-single-a(6), mod-transient-3(7), mod-16qam-87-percent-single(8), mod-transient-4(9), mod-64qam-75-percent-single(10), mod-transient-5(11), mod-64qam-92-percent-single(12), mod-transient-6(13), mod-256qam-81-percent-single(14), mod-16qam-63-percent-single-b(15), mod-16qam-63-percent-dual(16), mod-transient-7(17), mod-16qam-87-percent-dual(18), mod-transient-8(19), mod-64qam-75-percent-dual(20), mod-transient-9(21), mod-64qam-92-percent-dual(22), mod-transient-10(23), mod-256qam-81-percent-dual(24) } ACCESS read-only STATUS mandatory DESCRIPTION "The lowest modulation mode at which Second Data Service Ethernet traffic will be bridged over the wireless link" ::= { management 21 } -- PhyControl group attribute definitions -- linkSymmetry OBJECT-TYPE SYNTAX INTEGER { symmetry-adaptive(0), symmetry-2-to-1(1), symmetry-1-to-1(2), symmetry-1-to-2(3), symmetry-3-to-1(4), symmetry-1-to-3(5), symmetry-5-to-1(6), symmetry-1-to-5(7) } ACCESS read-only STATUS mandatory DESCRIPTION "Provides configuration options for sharing the available wireless capacity between the transmit and receive directions. Fixed link symmetry is defined by a ratio of the burst duration for the transmit direction to the burst duration for the receive direction. Permitted settings are 5:1, 3:1, 2:1, 1:1, 1:2, 1:3, 1:5. The 1:1 option provides fixed symmetric operation. The adaptive option selects transmit and receive burst durations automatically in response to the offered Ethernet traffic in each link direction. This attribute is valid only for a unit configured as a TDD Master" ::= { phyControl 1 } userConfiguredMaxModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-bpsk-63-percent(0), mod-qpsk-63-percent(1), mod-qpsk-87-percent(2), mod-16qam-63-percent(3), mod-16qam-87-percent(4), mod-64qam-75-percent(5), mod-64qam-92-percent(6), mod-256qam-81-percent(7) } ACCESS read-write STATUS mandatory DESCRIPTION "The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard" ::= { phyControl 2 } linkModeOptimization OBJECT-TYPE SYNTAX INTEGER { ip-traffic(0), tdm-traffic(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Optimizes the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimize transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimize transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols." ::= { phyControl 3 } txColorCode OBJECT-TYPE SYNTAX INTEGER { a(0), b(1), c(2), d(3), e(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Transmit Color Code. This attribute need only be considered when the unit is installed in a network of PTP units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link." ::= { phyControl 4 } rxColorCode OBJECT-TYPE SYNTAX INTEGER { a(0), b(1), c(2), d(3), e(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Receive Color Code. This attribute need only be considered when the unit is installed in a network of PTP units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link." ::= { phyControl 5 } remoteMaximumTransmitPower OBJECT-TYPE SYNTAX INTEGER (-15..30) ACCESS read-only STATUS mandatory DESCRIPTION "Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link" ::= { phyControl 6 } -- PhyStatus group attribute definitions -- linkLoss OBJECT-TYPE SYNTAX INTEGER (-500..500) ACCESS read-only STATUS mandatory DESCRIPTION "The wireless link loss expressed in tenths of a dB" ::= { phyStatus 1 } receivePower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Receive power expressed in tenths of a dBm" ::= { phyStatus 2 } vectorError OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB" ::= { phyStatus 3 } transmitPower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Transmit power expressed in tenths of a dBm" ::= { phyStatus 4 } receiveChannel OBJECT-TYPE SYNTAX INTEGER (0..63) ACCESS read-only STATUS mandatory DESCRIPTION "Current active receive channel" ::= { phyStatus 5 } transmitChannel OBJECT-TYPE SYNTAX INTEGER (0..63) ACCESS read-only STATUS mandatory DESCRIPTION "Current active transmit channel" ::= { phyStatus 6 } receiveFreqMHz OBJECT-TYPE SYNTAX INTEGER (0..6050) ACCESS read-only STATUS mandatory DESCRIPTION "Current receive frequency expressed in integer MHz" ::= { phyStatus 7 } transmitFreqMHz OBJECT-TYPE SYNTAX INTEGER (0..6050) ACCESS read-only STATUS mandatory DESCRIPTION "Current transmit frequency expressed in integer MHz" ::= { phyStatus 8 } signalStrengthRatio OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB" ::= { phyStatus 9 } receiveFreqKHz OBJECT-TYPE SYNTAX INTEGER (0..6050000) ACCESS read-only STATUS mandatory DESCRIPTION "Current receive frequency expressed as KHz" ::= { phyStatus 10 } transmitFreqKHz OBJECT-TYPE SYNTAX INTEGER (0..6050000) ACCESS read-only STATUS mandatory DESCRIPTION "Current transmit frequency expressed as KHz" ::= { phyStatus 11 } rawReceivePower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Raw receive power expressed in tenths of a dBm" ::= { phyStatus 12 } range OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Distance between the two peer wireless units expressed in tenths of a kilometer" ::= { phyStatus 13 } receiveModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-acquisition(0), mod-bpsk-63-percent(1), mod-qpsk-63-percent-single(2), mod-transient-1(3), mod-qpsk-87-percent-single(4), mod-transient-2(5), mod-16qam-63-percent-single-a(6), mod-transient-3(7), mod-16qam-87-percent-single(8), mod-transient-4(9), mod-64qam-75-percent-single(10), mod-transient-5(11), mod-64qam-92-percent-single(12), mod-transient-6(13), mod-256qam-81-percent-single(14), mod-16qam-63-percent-single-b(15), mod-16qam-63-percent-dual(16), mod-transient-7(17), mod-16qam-87-percent-dual(18), mod-transient-8(19), mod-64qam-75-percent-dual(20), mod-transient-9(21), mod-64qam-92-percent-dual(22), mod-transient-10(23), mod-256qam-81-percent-dual(24) } ACCESS read-only STATUS mandatory DESCRIPTION "Current active receive modulation mode" ::= { phyStatus 14 } transmitModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-acquisition(0), mod-bpsk-63-percent(1), mod-qpsk-63-percent-single(2), mod-transient-1(3), mod-qpsk-87-percent-single(4), mod-transient-2(5), mod-16qam-63-percent-single-a(6), mod-transient-3(7), mod-16qam-87-percent-single(8), mod-transient-4(9), mod-64qam-75-percent-single(10), mod-transient-5(11), mod-64qam-92-percent-single(12), mod-transient-6(13), mod-256qam-81-percent-single(14), mod-16qam-63-percent-single-b(15), mod-16qam-63-percent-dual(16), mod-transient-7(17), mod-16qam-87-percent-dual(18), mod-transient-8(19), mod-64qam-75-percent-dual(20), mod-transient-9(21), mod-64qam-92-percent-dual(22), mod-transient-10(23), mod-256qam-81-percent-dual(24) } ACCESS read-only STATUS mandatory DESCRIPTION "Current active transmit modulation mode" ::= { phyStatus 15 } searchState OBJECT-TYPE SYNTAX INTEGER { registering(0), searching(1), acquiring(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal." ::= { phyStatus 16 } -- Alarms group attribute definitions -- unitOutOfCalibration OBJECT-TYPE SYNTAX INTEGER { calibrated(0), partial-calibration(1), invalid-calibration(2), bandwidth-variant-unsupported-pas-shutdown(3), out-of-calibration-pas-shutdown(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The unit is out of calibration" ::= { alarms 1 } incompatibleRegulatoryBands OBJECT-TYPE SYNTAX INTEGER { reg-ok(0), reg-incompatible-license-keys(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys" ::= { alarms 4 } noWirelessChannelAvailable OBJECT-TYPE SYNTAX INTEGER { ok(0), no-wireless-channel-available(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Spectrum Management was unable to locate a suitable wireless channel to operate on" ::= { alarms 5 } wirelessLinkDisabledWarning OBJECT-TYPE SYNTAX INTEGER { ok(0), disabled-by-snmp-ifadminstatus(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic" ::= { alarms 6 } mainPSUPortDisabledWarning OBJECT-TYPE SYNTAX INTEGER { ok(0), disabled-by-snmp-ifadminstatus(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= { alarms 7 } sFPError OBJECT-TYPE SYNTAX INTEGER { ok(0), installed-sfp-not-licensed(1), fiber-link-not-established-but-los-not-detected(2), fiber-link-not-established-and-los-detected(3), installed-sfp-not-supported(4), sfp-initialization-failed(5) } ACCESS read-only STATUS mandatory DESCRIPTION "If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert" ::= { alarms 8 } mainPSUPortConfigurationMismatch OBJECT-TYPE SYNTAX INTEGER { no-error(0), mismatch-detected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch" ::= { alarms 9 } incompatibleMasterAndSlave OBJECT-TYPE SYNTAX INTEGER { ok(0), incompatible-product-variants(1), different-software-versions-running(2) } ACCESS read-only STATUS mandatory DESCRIPTION "A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert" ::= { alarms 10 } tDDSynchronizationStatus OBJECT-TYPE SYNTAX INTEGER { locked(0), holdover(1), holdover-no-gpssync-in(2), not-synchronized(3), not-synchronized-no-gpssync-in(4), ptp-sync-not-connected(5), initialising(6), cluster-timing-master(7), acquiring-lock(8), inactive(9) } ACCESS read-only STATUS mandatory DESCRIPTION "An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference." ::= { alarms 11 } auxPortDisabledWarning OBJECT-TYPE SYNTAX INTEGER { ok(0), disabled-by-snmp-ifadminstatus(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= { alarms 12 } tDDSynchronizationAlarm OBJECT-TYPE SYNTAX INTEGER { ok(0), synchronization-lost(1), reference-signal-lost(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired." ::= { alarms 13 } linkModeOptimizationMismatch OBJECT-TYPE SYNTAX INTEGER { ok(0), link-mode-optimization-mismatch(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The remote node of this link has been configured with a different link mode optimization" ::= { alarms 14 } auxPortConfigurationMismatch OBJECT-TYPE SYNTAX INTEGER { no-error(0), mismatch-detected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured." ::= { alarms 15 } secureModeAlarm OBJECT-TYPE SYNTAX INTEGER { secure-mode-is-active(0), secure-mode-is-not-configured(1), secure-mode-is-configured-but-not-active(2), secure-mode-is-not-supported(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image." ::= { alarms 16 } dataBridgingStatusAlarm OBJECT-TYPE SYNTAX INTEGER { bridging-enabled(0), bridging-disabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode" ::= { alarms 17 } sFPPortDisabledWarning OBJECT-TYPE SYNTAX INTEGER { ok(0), disabled-by-snmp-ifadminstatus(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= { alarms 18 } sFPPortConfigurationMismatch OBJECT-TYPE SYNTAX INTEGER { no-error(0), mismatch-detected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured." ::= { alarms 19 } maxLinkRangeExceeded OBJECT-TYPE SYNTAX INTEGER { max-link-range-ok(0), max-link-range-exceeded(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active." ::= { alarms 20 } nIDULanPortDisabledWarning OBJECT-TYPE SYNTAX INTEGER { ok(0), disabled-by-snmp-ifadminstatus(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= { alarms 21 } nIDULanPortConfigurationMismatch OBJECT-TYPE SYNTAX INTEGER { no-error(0), mismatch-detected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch." ::= { alarms 22 } portAllocationMismatch OBJECT-TYPE SYNTAX INTEGER { port-allocation-ok(0), mismatch-in-second-data-service(1), mismatch-in-out-of-band-remote-management-service(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The local and remote ODUs have different services configured." ::= { alarms 23 } secondDataBridgingStatusAlarm OBJECT-TYPE SYNTAX INTEGER { bridging-enabled(0), bridging-disabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Bridging of Ethernet traffic from Second Data Service has been disabled because the wireless link is not operating at the configured Lowest Second Data Modulation Mode" ::= { alarms 24 } transparentClockSourcePortAlarm OBJECT-TYPE SYNTAX INTEGER { ok(0), invalid-transparent-clock-source-port(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Transparent Clock will not function properly because SFP, the selected clock source port is not FIBER" ::= { alarms 25 } -- Smtp group attribute definitions -- sMTPEmailAlert OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address" ::= { smtp 1 } sMTPServerPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "Port number of the SMTP server" ::= { smtp 3 } sMTPSourceEmailAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "The 'from' email address used when constructing the automatically generated e-mail message" ::= { smtp 4 } sMTPDestinationEmailAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "The 'to' email address used when constructing the automatically generated e-mail message" ::= { smtp 5 } sMTPEnabledMessages OBJECT-TYPE SYNTAX BITS { nidu-lan-port-up-down(0), sfp-port-up-down(1), aux-port-up-down(2), main-psu-port-up-down(3), enabled-diagnostic-alarms(4), dfs-impulse-interference(5), channel-change(6), wireless-link-up-down(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This controls which SMTP messages the unit will send" ::= { smtp 6 } sMTPServerInternetAddressType OBJECT-TYPE SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown-6(5), unknown-7(6), unknown-8(7), unknown-9(8), unknown-10(9), unknown-11(10), unknown-12(11), unknown-13(12), unknown-14(13), unknown-15(14), unknown-16(15), dns(16) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of Internet address specified by the associated sMTPServerInternetAddress." ::= { smtp 7 } sMTPServerInternetAddress OBJECT-TYPE SYNTAX InetAddress ACCESS read-write STATUS mandatory DESCRIPTION "Internet address of the SMTP server" ::= { smtp 8 } -- SnmpControl group attribute definitions -- sNMPPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute" ::= { snmpControl 1 } sNMPCommunityString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "The SNMP community string. NB: A system reboot is required to activate changes to this attribute" ::= { snmpControl 2 } sNMPTrapTableNumber OBJECT-TYPE SYNTAX INTEGER (2) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the sNMPTrapTable." ::= { snmpControl 3 } sNMPTrapVersion OBJECT-TYPE SYNTAX INTEGER { v1(0), v2c(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute" ::= { snmpControl 5 } sNMPEnabledTraps OBJECT-TYPE SYNTAX BITS { aux-port-up-down(0), main-psu-port-up-down(1), authentication-failure(2), enabled-diagnostic-alarms(3), dfs-impulse-interference(4), channel-change(5), wireless-link-up-down(6), cold-start(7), nidu-lan-port-up-down(14), sfp-port-up-down(15) } ACCESS read-write STATUS mandatory DESCRIPTION "This controls which SNMP Traps the unit will send" ::= { snmpControl 6 } enabledDiagnosticAlarms OBJECT-TYPE SYNTAX BITS { port-state(0), incompatible-master-and-slave(1), incompatible-regulatory-bands(2), maximum-link-range-exceeded(3), unit-out-of-calibration(4), install-arm-state(5), install-status(6), regulatory-band(7), syslog-local-wrapped(8), syslog-local-nearly-full(9), syslog-disabled-warning(10), link-mode-optimization-mismatch(11), tdd-synchronization-alarm(12), wireless-link-disabled-warning(13), sntp-synchronization-failed(14), no-wireless-channel-available(15), tdm-alarms(18), capacity-variant-mismatch(19), remaining-full-capacity-trial-time(20), data-bridging-status(21), unknown-18(22), syslog-client-disabled-warning(23) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes" ::= { snmpControl 7 } sNMPSendAllTrapsAtStartup OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up." ::= { snmpControl 8 } -- SNMPTrapTable group attribute definitions -- sNMPTrapTableIndex OBJECT-TYPE SYNTAX INTEGER (1..2) ACCESS not-accessible STATUS mandatory DESCRIPTION "SNMP trap value, used to index the SNMPTrapTable." ::= { sNMPTrapTableEntry 1 } sNMPTrapPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "Destination port for SNMP Traps (default=162). NB: A system reboot is required to activate changes to this attribute." ::= { sNMPTrapTableEntry 3 } sNMPTrapInternetAddressType OBJECT-TYPE SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown-6(5), unknown-7(6), unknown-8(7), unknown-9(8), unknown-10(9), unknown-11(10), unknown-12(11), unknown-13(12), unknown-14(13), unknown-15(14), unknown-16(15), dns(16) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of Internet address specified by the associated sNMPTrapInternetAddress." ::= { sNMPTrapTableEntry 4 } sNMPTrapInternetAddress OBJECT-TYPE SYNTAX InetAddress ACCESS read-write STATUS mandatory DESCRIPTION "The Internet address to which all SNMP Traps are sent." ::= { sNMPTrapTableEntry 5 } sNMPTrapReceiverEnabled OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "A value of 0 disables the sending of SNMP trap to corresponding receiver. A value of 1 enables the sending of SNMP trap to corresponding receiver." ::= { sNMPTrapTableEntry 6 } -- Sntp group attribute definitions -- sNTPState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "SNTP control state" ::= { sntp 1 } sNTPPollInterval OBJECT-TYPE SYNTAX INTEGER (60..43200) ACCESS read-write STATUS mandatory DESCRIPTION "The SNTP server polling interval" ::= { sntp 4 } sNTPSync OBJECT-TYPE SYNTAX INTEGER { no-sync(0), in-sync(1) } ACCESS read-only STATUS mandatory DESCRIPTION "If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP" ::= { sntp 5 } sNTPLastSync OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Last SNTP sync time" ::= { sntp 6 } systemClock OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "System clock presented as local time" ::= { sntp 7 } timeZone OBJECT-TYPE SYNTAX INTEGER { gmt-minus-1200(0), gmt-minus-1130(1), gmt-minus-1100(2), gmt-minus-1030(3), gmt-minus-1000(4), gmt-minus-0930(5), gmt-minus-0900(6), gmt-minus-0830(7), gmt-minus-0800(8), gmt-minus-0730(9), gmt-minus-0700(10), gmt-minus-0630(11), gmt-minus-0600(12), gmt-minus-0530(13), gmt-minus-0500(14), gmt-minus-0430(15), gmt-minus-0400(16), gmt-minus-0330(17), gmt-minus-0300(18), gmt-minus-0230(19), gmt-minus-0200(20), gmt-minus-0130(21), gmt-minus-0100(22), gmt-minus-0030(23), gmt-zero(24), gmt-plus-0030(25), gmt-plus-0100(26), gmt-plus-0130(27), gmt-plus-0200(28), gmt-plus-0230(29), gmt-plus-0300(30), gmt-plus-0330(31), gmt-plus-0400(32), gmt-plus-0430(33), gmt-plus-0500(34), gmt-plus-0530(35), gmt-plus-0600(36), gmt-plus-0630(37), gmt-plus-0700(38), gmt-plus-0730(39), gmt-plus-0800(40), gmt-plus-0830(41), gmt-plus-0900(42), gmt-plus-0930(43), gmt-plus-1000(44), gmt-plus-1030(45), gmt-plus-1100(46), gmt-plus-1130(47), gmt-plus-1200(48), gmt-plus-1230(49), gmt-plus-1300(50) } ACCESS read-write STATUS mandatory DESCRIPTION "Time zone offsets from Greenwich Mean Time (GMT)" ::= { sntp 8 } daylightSaving OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Daylight Saving Time" ::= { sntp 9 } sNTPPrimaryServer OBJECT-TYPE SYNTAX INTEGER { server-1(0), server-2(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the primary SNTP server, determining the order in which the servers are tried." ::= { sntp 10 } sNTPPrimaryServerDeadTime OBJECT-TYPE SYNTAX INTEGER (0..86400) ACCESS read-write STATUS mandatory DESCRIPTION "Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer." ::= { sntp 11 } sNTPServerRetries OBJECT-TYPE SYNTAX INTEGER (0..10) ACCESS read-write STATUS mandatory DESCRIPTION "Number of times the PTP will retry after an SNTP server fails to respond." ::= { sntp 12 } sNTPServerTimeout OBJECT-TYPE SYNTAX INTEGER (1..15) ACCESS read-write STATUS mandatory DESCRIPTION "Time (in seconds) the PTP will wait for a response from an SNTP server." ::= { sntp 13 } sNTPServerTableNumber OBJECT-TYPE SYNTAX INTEGER (2) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the SNTPServerTable." ::= { sntp 14 } -- SNTPServerTable group attribute definitions -- sNTPServerTableIndex OBJECT-TYPE SYNTAX INTEGER (1..2) ACCESS not-accessible STATUS mandatory DESCRIPTION "Index range for the SNTPServerTable." ::= { sNTPServerTableEntry 1 } sNTPServerPortNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The IP port number of the SNTP server. Defaults to port 123." ::= { sNTPServerTableEntry 3 } sNTPServerStatus OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) ACCESS read-only STATUS mandatory DESCRIPTION "Status message reflecting the result of communications with the SNTP server when last polled" ::= { sNTPServerTableEntry 4 } sNTPServerInternetAddressType OBJECT-TYPE SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown-6(5), unknown-7(6), unknown-8(7), unknown-9(8), unknown-10(9), unknown-11(10), unknown-12(11), unknown-13(12), unknown-14(13), unknown-15(14), unknown-16(15), dns(16) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of Internet address specified by the associated sNTPServerInternetAddress." ::= { sNTPServerTableEntry 5 } sNTPServerInternetAddress OBJECT-TYPE SYNTAX InetAddress ACCESS read-write STATUS mandatory DESCRIPTION "The Internet address of a valid SNTP server" ::= { sNTPServerTableEntry 6 } -- Reset group attribute definitions -- systemReset OBJECT-TYPE SYNTAX INTEGER { running(0), console-reboot(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory" ::= { reset 1 } -- Versions group attribute definitions -- softwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-only STATUS mandatory DESCRIPTION "Current software version" ::= { versions 1 } hardwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-only STATUS mandatory DESCRIPTION "Hardware platform version" ::= { versions 2 } secondarySoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-only STATUS mandatory DESCRIPTION "Secondary software version, used when the primary software image is invalid or erased" ::= { versions 3 } bootVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-only STATUS mandatory DESCRIPTION "Boot code software version" ::= { versions 4 } -- PubStats group attribute definitions -- receiveDataRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Average data rate over the last one second interval (kbps)" ::= { pubStats 1 } transmitDataRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Average data rate over the last one second interval (kbps)" ::= { pubStats 2 } aggregateDataRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Average data rate over the last one second interval (kbps)" ::= { pubStats 3 } wirelessLinkAvailability OBJECT-TYPE SYNTAX INTEGER (0..1000000) ACCESS read-only STATUS mandatory DESCRIPTION "Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision" ::= { pubStats 4 } wirelessLinkStatus OBJECT-TYPE SYNTAX INTEGER { up(0), registering(1), searching(2), acquiring(3), radar-cac(4), initialising(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of the wireless link" ::= { pubStats 5 } byteErrorRatio OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Reciprocal of the byte error ratio calculated since the last reset of the system counters" ::= { pubStats 6 } receiveModulationModeDetail OBJECT-TYPE SYNTAX INTEGER { running-at-maximum-receive-mode(0), running-at-user-configured-max-modulation-mode(1), restricted-because-installation-is-armed(2), restricted-because-of-byte-errors-on-the-wireless-link(3), restricted-because-the-link-parameters-are-updating(4), restricted-because-channel-change-is-in-progress(5), restricted-due-to-the-low-ethernet-link-speed(6), running-at-maximum-receive-mode-for-channel-bandwidth(7), limited-by-the-wireless-conditions(8), restricted-because-full-capability-trial-license-expired(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The reason for the current receive modulation mode" ::= { pubStats 7 } dataBridgingAvailability OBJECT-TYPE SYNTAX INTEGER (0..1000000) ACCESS read-only STATUS mandatory DESCRIPTION "Link availability bridging Ethernet Data traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision" ::= { pubStats 8 } -- Encryption group attribute definitions -- encryptionAlgorithm OBJECT-TYPE SYNTAX INTEGER { none(0), aes-rijndael(1), aes-192-bit-rijndael(2), aes-256-bit-rijndael(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly" ::= { encryption 1 } -- TDDControl group attribute definitions -- tDDSynchronizationMode OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "TDD Synchronization Mode selection" ::= { tDDControl 1 } -- AAAControl group attribute definitions -- userTableNumber OBJECT-TYPE SYNTAX INTEGER (1..10) ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the userTable" ::= { aAAControl 1 } -- UserTable group attribute definitions -- userTableIndex OBJECT-TYPE SYNTAX INTEGER (1..10) ACCESS not-accessible STATUS mandatory DESCRIPTION "used to index values in the userTable." ::= { userTableEntry 1 } userName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..67)) ACCESS read-only STATUS mandatory DESCRIPTION "User name which must be entered, along with the appropriate password, in order to gain access to the system." ::= { userTableEntry 2 } userRole OBJECT-TYPE SYNTAX INTEGER { read-only(0), system-administrator(1), security-officer(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes." ::= { userTableEntry 3 } userEnabled OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Enable / Disable the selected user" ::= { userTableEntry 4 } userPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..67)) ACCESS read-write STATUS mandatory DESCRIPTION "User password, which must be entered in order to gain access to the system." ::= { userTableEntry 5 } -- SyslogControl group attribute definitions -- syslogClient OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Enable or disable the syslog client" ::= { syslogControl 1 } syslogState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The syslog service has been enabled or disabled" ::= { syslogControl 2 } -- RouterProtocols group attribute definitions -- microwaveAdaptiveBandwidth OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Enable support of Microwave Adaptive Bandwidth Protocol. MAB is disabled if link symmetry is configured as Adaptive" ::= { routerProtocols 1 } mABNominalModulationMode OBJECT-TYPE SYNTAX INTEGER { mod-acquisition(0), mod-bpsk-63-percent(1), mod-qpsk-63-percent-single(2), mod-transient-1(3), mod-qpsk-87-percent-single(4), mod-transient-2(5), mod-16qam-63-percent-single-a(6), mod-transient-3(7), mod-16qam-87-percent-single(8), mod-transient-4(9), mod-64qam-75-percent-single(10), mod-transient-5(11), mod-64qam-92-percent-single(12), mod-transient-6(13), mod-256qam-81-percent-single(14), mod-16qam-63-percent-single-b(15), mod-16qam-63-percent-dual(16), mod-transient-7(17), mod-16qam-87-percent-dual(18), mod-transient-8(19), mod-64qam-75-percent-dual(20), mod-transient-9(21), mod-64qam-92-percent-dual(22), mod-transient-10(23), mod-256qam-81-percent-dual(24) } ACCESS read-only STATUS mandatory DESCRIPTION "The Nominal modulation mode is the desired modulation mode. MAB VSM packets are generated when the current modulation mode falls below the nominal modulation." ::= { routerProtocols 2 } mABTransmissionInterval OBJECT-TYPE SYNTAX INTEGER { transmission-interval-1-s(0), transmission-interval-10-s(1), transmission-interval-60-s(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The minimum interval (in seconds) between successive MAB vendor specific messages (VSM). These VSM are sent when the current transmit capacity falls below the configured MAB Nominal Modulation Mode." ::= { routerProtocols 3 } mABHoldoffPeriod OBJECT-TYPE SYNTAX INTEGER (10..60) ACCESS read-only STATUS mandatory DESCRIPTION "The period (in seconds) over which transmit capacity is averaged over to determine when the wireless link has degraded" ::= { routerProtocols 4 } mABMaintenanceLevel OBJECT-TYPE SYNTAX INTEGER (0..7) ACCESS read-only STATUS mandatory DESCRIPTION "Maintenance Levels (0-7) determines the destination MAC address of MAB vendor specific messages." ::= { routerProtocols 5 } useVLANForMABProtocol OBJECT-TYPE SYNTAX INTEGER { no-vlan-tagging(0), ieee-8021q-tagged-c-tag-type-8100(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This controls whether MAB vendor specific messages (VSM) packets use VLAN tags or not." ::= { routerProtocols 6 } mABProtocolVID OBJECT-TYPE SYNTAX INTEGER (0..4094) ACCESS read-only STATUS mandatory DESCRIPTION "This VLAN VID (0-4094) will be included in MAB vendor specific messages (VSM) packets." ::= { routerProtocols 7 } mABProtocolVLANPriority OBJECT-TYPE SYNTAX INTEGER (0..7) ACCESS read-only STATUS mandatory DESCRIPTION "This VLAN Priority (0-7) will be included in MAB vendor specific messages (VSM) packets." ::= { routerProtocols 8 } mABState OBJECT-TYPE SYNTAX INTEGER { normal(0), degraded(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Current state of MAB Protocol. A state of 'Normal' on a green background indicates that a PTP link is operating at nominal capacity" ::= { routerProtocols 9 } mABNominalTransmitCapacity OBJECT-TYPE SYNTAX INTEGER (0..1000) ACCESS read-only STATUS mandatory DESCRIPTION "The nominal Tx capacity used in MAB Vendor Specific Messages for the selected nominal modulation mode " ::= { routerProtocols 10 } mABCurrentTransmitCapacity OBJECT-TYPE SYNTAX INTEGER (0..1000) ACCESS read-only STATUS mandatory DESCRIPTION "The current Tx capacity of the wireless link used in the last MAB Vendor Specific Message transmitted." ::= { routerProtocols 11 } -- CableDiagnostics group attribute definitions -- cableDiagnosticsPorts OBJECT-TYPE SYNTAX BITS { aux-port(6), main-psu-port(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Select ports on which Cable Diagnostics must be executed" ::= { cableDiagnostics 1 } cableDiagnosticsControl OBJECT-TYPE SYNTAX INTEGER { start-test(0), test-in-progress(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Set this attribute to 'Test in Progress' to start a Cable Diagnostics test" ::= { cableDiagnostics 2 } cableDiagnosticsWarning OBJECT-TYPE SYNTAX INTEGER { idle(0), test-in-progress(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Normal Ethernet operation is disrupted when a Cable Diagnostics test is in progress" ::= { cableDiagnostics 3 } cableDiagnosticsResultTableNumber OBJECT-TYPE SYNTAX INTEGER (1..2) ACCESS read-only STATUS mandatory DESCRIPTION "Number of rows in the Cable Diagnostics Result Table." ::= { cableDiagnostics 4 } -- CableDiagnosticsResultTable group attribute definitions -- cableDiagnosticsResultTableIndex OBJECT-TYPE SYNTAX INTEGER (1..2) ACCESS not-accessible STATUS mandatory DESCRIPTION "Cable Diagnostics Port value used to index into the result table." ::= { cableDiagnosticsResultTableEntry 1 } cableDiagnosticsResultsDateTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Date and Time when a Cable Diagnostics test was last executed" ::= { cableDiagnosticsResultTableEntry 2 } cableDiagPair1Results OBJECT-TYPE SYNTAX INTEGER { ok(0), unknown(1), in-progress(2), not-tested(3), open-circuit(4), short-circuit(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The result of the most recent execution of Cable Diagnostics on cable pair 1. According to the T658B wiring scheme, pair 1 is pins 4 & 5 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test." ::= { cableDiagnosticsResultTableEntry 3 } cableDiagPair1Distance OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet)." ::= { cableDiagnosticsResultTableEntry 4 } cableDiagPair2Results OBJECT-TYPE SYNTAX INTEGER { ok(0), unknown(1), in-progress(2), not-tested(3), open-circuit(4), short-circuit(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The result of the most recent execution of Cable Diagnostics on cable pair 2. According to the T658B wiring scheme, pair 2 is pins 1 & 2 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test." ::= { cableDiagnosticsResultTableEntry 5 } cableDiagPair2Distance OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet)." ::= { cableDiagnosticsResultTableEntry 6 } cableDiagPair3Results OBJECT-TYPE SYNTAX INTEGER { ok(0), unknown(1), in-progress(2), not-tested(3), open-circuit(4), short-circuit(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The result of the most recent execution of Cable Diagnostics on cable pair 3. According to the T658B wiring scheme, pair 3 is pins 3 & 6 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test." ::= { cableDiagnosticsResultTableEntry 7 } cableDiagPair3Distance OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet)." ::= { cableDiagnosticsResultTableEntry 8 } cableDiagPair4Results OBJECT-TYPE SYNTAX INTEGER { ok(0), unknown(1), in-progress(2), not-tested(3), open-circuit(4), short-circuit(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The result of the most recent execution of Cable Diagnostics on cable pair 4. According to the T658B wiring scheme, pair 4 is pins 7 & 8 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test." ::= { cableDiagnosticsResultTableEntry 9 } cableDiagPair4Distance OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet)." ::= { cableDiagnosticsResultTableEntry 10 } -- Supplementary group attribute definitions -- longitude OBJECT-TYPE SYNTAX DisplayString (SIZE(0..19)) ACCESS read-write STATUS mandatory DESCRIPTION "The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function." ::= { supplementary 1 } latitude OBJECT-TYPE SYNTAX DisplayString (SIZE(0..19)) ACCESS read-write STATUS mandatory DESCRIPTION "The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function." ::= { supplementary 2 } altitude OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The altitude of the unit, measured in meters. This object is set by the SNMP manager and has no internal function." ::= { supplementary 3 } -- Enterprise TRAP definitions -- channelChangeTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { receiveChannel } DESCRIPTION "The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference." ::= 1 dfsImpulsiveInterferenceTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { receiveChannel } DESCRIPTION "DFS impulsive interference detected event" ::= 2 mainPSUPortStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { mainPSUPortStatus } DESCRIPTION "Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= 3 mainPSUPortDisabledWarningTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { mainPSUPortDisabledWarning } DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= 4 mainPSUPortConfigurationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { mainPSUPortConfigurationMismatch } DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch" ::= 5 auxPortStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { auxPortStatus } DESCRIPTION "Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= 6 auxPortDisabledWarningTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { auxPortDisabledWarning } DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= 7 regulatoryBandTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { regulatoryBand } DESCRIPTION "The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key. NB: a change of state may generate an SNMP trap and/or SMTP email alert." ::= 8 installStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { installStatus } DESCRIPTION "A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert" ::= 9 installArmStateTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { installArmState } DESCRIPTION "Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= 10 unitOutOfCalibrationTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { unitOutOfCalibration } DESCRIPTION "The unit is out of calibration" ::= 11 auxPortPowerOverEthernetOutputStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { auxPortPowerOverEthernetOutputStatus } DESCRIPTION "Current status of the Power Over Ethernet (PoE) output of the Aux port" ::= 12 incompatibleRegulatoryBandsTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { incompatibleRegulatoryBands } DESCRIPTION "The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys" ::= 14 noWirelessChannelAvailableTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { noWirelessChannelAvailable } DESCRIPTION "Spectrum Management was unable to locate a suitable wireless channel to operate on" ::= 15 wirelessLinkDisabledWarningTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { wirelessLinkDisabledWarning } DESCRIPTION "The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic" ::= 16 auxPortConfigurationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { auxPortConfigurationMismatch } DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured." ::= 17 sFPErrorTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { sFPError } DESCRIPTION "If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert" ::= 18 sFPPortStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { sFPPortStatus } DESCRIPTION "Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= 19 incompatibleMasterAndSlaveTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { incompatibleMasterAndSlave } DESCRIPTION "A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert" ::= 20 sNTPSyncTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { sNTPSync } DESCRIPTION "If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP" ::= 21 tDDSynchronizationAlarmTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { tDDSynchronizationAlarm } DESCRIPTION "Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired." ::= 22 sFPPortDisabledWarningTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { sFPPortDisabledWarning } DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= 23 sFPPortConfigurationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { sFPPortConfigurationMismatch } DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured." ::= 24 linkModeOptimizationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { linkModeOptimizationMismatch } DESCRIPTION "The remote node of this link has been configured with a different link mode optimization" ::= 25 tDMInterfaceStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { tDMInterfaceStatus } DESCRIPTION "@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used" ::= 26 tDMChannelStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { tDMChannelStatus } DESCRIPTION "Current status of the TDM channels. A value of 0 indicates that a TDM channel is established" ::= 27 tDMChannelLoopbackTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { tDMChannelLoopback } DESCRIPTION "The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= 28 nIDULanPortStatusTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { nIDULanPortStatus } DESCRIPTION "Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert" ::= 29 syslogStateTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { syslogState } DESCRIPTION "The syslog service has been enabled or disabled" ::= 30 syslogLocalNearlyFullTrap TRAP-TYPE ENTERPRISE ptpTraps DESCRIPTION "The syslog local log is nearly full (90%)" ::= 31 syslogLocalWrappedTrap TRAP-TYPE ENTERPRISE ptpTraps DESCRIPTION "The syslog local log has wrapped" ::= 32 syslogClientTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { syslogClient } DESCRIPTION "Enable or disable the syslog client" ::= 33 secureModeAlarmTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { secureModeAlarm } DESCRIPTION "The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image." ::= 34 dataBridgingStatusAlarmTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { dataBridgingStatusAlarm } DESCRIPTION "Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode" ::= 35 licenseRemainingTrialPeriodAlarmTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { licenseRemainingTrialPeriodAlarm } DESCRIPTION "If the full capability trial license period is about to expire then purchase a license upgrade from your reseller." ::= 36 capacityVariantMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { capacityVariantMismatch } DESCRIPTION "The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity." ::= 37 maxLinkRangeExceededTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { maxLinkRangeExceeded } DESCRIPTION "The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active." ::= 38 tDMConfigurationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { tDMConfigurationMismatch } DESCRIPTION "Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end." ::= 39 nIDULanPortDisabledWarningTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { nIDULanPortDisabledWarning } DESCRIPTION "The SNMP ifAdminStatus of the interface has disabled Ethernet traffic" ::= 40 nIDULanPortConfigurationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { nIDULanPortConfigurationMismatch } DESCRIPTION "The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch." ::= 41 secondDataBridgingStatusAlarmTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { secondDataBridgingStatusAlarm } DESCRIPTION "Bridging of Ethernet traffic from Second Data Service has been disabled because the wireless link is not operating at the configured Lowest Second Data Modulation Mode" ::= 42 transparentClockSourcePortAlarmTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { transparentClockSourcePortAlarm } DESCRIPTION "Transparent Clock will not function properly because SFP, the selected clock source port is not FIBER" ::= 43 portAllocationMismatchTrap TRAP-TYPE ENTERPRISE ptpTraps VARIABLES { portAllocationMismatch } DESCRIPTION "The local and remote ODUs have different services configured." ::= 44 END 5. References [1] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, SNMP Research, S. Whitaker [Page 2] RFC DRAFT Cambium PTP MIB February 2015 Performance Systems International, Performance Systems International, MIT Laboratory for Computer Science, May 1990. [2] McCloghrie K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets", STD 17, RFC 1213, Performance Systems International, March 1991. [3] Information processing systems - Open Systems Interconnection - Specification of Abstract Syntax Notation One (ASN.1), International Organization for Standardization, International Standard 8824, December 1987. [4] Information processing systems - Open Systems Interconnection - Specification of Basic Encoding Rules for Abstract Notation One (ASN.1), International Organization for Standardization, International Standard 8825, December 1987. [5] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions", STD 16, RFC 1212, Performance Systems International, Hughes LAN Systems, March 1991. [6] Rose, M., Editor, "A Convention for Defining Traps for use with the SNMP", RFC 1215, Performance Systems International, March 1991. [7] ANSI/IEEE Standard 802.1D-1990 MAC Bridges, IEEE Project 802 Local and Metropolitan Area Networks, (March 8, 1991). 6. Security Considerations Security issues are not discussed in this memo. 7. Authors' Addresses Simon Whitaker Cambium Networks Ltd. Unit B2, Linhay Business Park, Eastern Road, Ashburton, Devon. TQ13 7UP United Kingdom Phone: +44 (0) 1364 655 500 Email: simon.whitaker@cambiumnetworks.com