Sharing Standard Templates for NetXMS
-
WD MyCloud SNMP Template
Applies to:
- Systems with SNMP Object ID of .1.3.6.1.4.1.5127.1.1.1.2
Note:
- The Capacity Used % is a scripted DCI, the device itself does not provide a direct % for alerting. The DCI does not rely on the Total and Free DCIs, but collects both values independently via SNMP. If you have a range of these devices, it's probably worth changing the script.
-
Synology NAS SNMP Template
Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.8072.* and a valid response for SNMP OID .1.3.6.1.4.1.6574.1.5.1.0.
-
Netgear ReadyNAS SNMP Template
Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.4526.100.16.* or System Description matching "ReadyDATA OS".
-
QNAP NAS SNMP Template
Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.24681.* and a valid response for SNMP OID .1.3.6.1.4.1.24681.1.4.1.1.1.1.4.2.0. (QNAP NAS Template)
- Systems with SNMP Object ID matching .1.3.6.1.4.1.24681.* and no valid response for SNMP OID .1.3.6.1.4.1.24681.1.4.1.1.1.1.4.2.0. (QNAP NAS (old) Template)
Notes:
I am unsure at which firmware version the new MIB kicked in. It also appears some older models even with the latest firmware are still using the old MIB. The extra check for the OID above seems to work well for identification though.Also attached a separate template with three QNAP SNMP Traps (QNAP appears to simply send Inform/Warning/Error traps with different messages) and matching events.
-
WatchGuard Firewall SNMP Template
Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.3097.* (WatchGuard Template)
- Systems with SNMP Object ID matching .1.3.6.1.4.1.3097.* and a valid response for SNMP OID .1.3.6.1.4.1.3097.6.6.1.0 (WatchGuard FireCluster Template)
Note:
- The Used RAM % is a scripted DCI, the device itself does not provide a direct % for alerting. The DCI does not rely on the Installed/Free RAM DCIs, but collects both values independently via SNMP. If you have a range of these devices, it's probably worth changing the script.
Also attached a separate template with a simple SNMP Trap for Alerts triggered by WatchGuards. Every alert triggers the same trap.
Configuring alerts via SNMP Traps is a bit of a pain in Watchguards, as you need to enable SNMP, configure the destination and enable alerts in every little service/proxy/whatever you might want to get alerts for..
-
SonicWALL SNMP Template
Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.8741.1
Note:
- The Concurrent Connections % is a scripted DCI, the device itself does not provide a direct % for alerting. The DCI does not rely on the Maximum and Current DCIs, but collects both values independently via SNMP. If you have a range of these devices, it's probably worth changing the script.
-
Ruckus Brocade ICX SNMP Template
Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.1991.*, but not .1.3.6.1.4.1.1991.1.3.52.2.4.1.1.
-
TP Link Switch SNMP Template
Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.11863.5.*
Note:
- We only monitor one of these and it's not returning a lot of data (that we found useful from a monitoring perspective), so the template is fairly simple.
-
UniFi Switch SNMP Template
Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.4413 and system description starting with "USW-".
Notes:
- We are monitoring only one of these and the above looks like it should work for other UniFi switches if this one device is anything to go by. Problem with .1.3.6.1.4.1.4413 is that it is the Broadcom Enterprise, so could potentially be matching a lot of other devices if it wasn't for the additional system description restriction. As all data for the UniFi switch is also located in the Broadcom Enterprise, this could maybe be turned into a more generic Broadcom template (someone with matching devices would be able to confirm this).
-
Lenovo XClarity / IBM Integrated Management Console SNMP Traps Template
The traps all contain the same varbinds. The trap configuration in this template pick out the following:
- Datetime
- Priority
- Message Text
- Message ID Prefix
The Event includes the Datetime, Prefix and Message Text.
Priority is read inside the Event Processing policy, which changes the Events severity as needed. The policy is effectively used as "SNMP Trap Transform Script".No policy for alerting is included, but that could be done inside the included policy or by adding another one below it (processing does not stop at the transform policy).
SNMP Traps - Lenovo XCC, IBM IMM.xml
-
Cisco 3/4G SNMP Template
Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.9.1.* and a valid entry in the .1.3.6.1.4.1.9.9.661.1.1.1.1 table.
-
Xirrus Access Point SNMP Template
Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.21013.1.*
Notes:
- Default SNMP Community for Xirrus access points is xirrus.
-
Ruckus ZoneDirector SNMP Template
Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.25053.3.1.5.*
Note:
- Unnamed WAPs in ZoneDirector will show up with the same instance name, making it difficult to tell them apart. It is recommended to ensure they all have proper names.
-
Ubiquiti AirMAX SNMP Template
Applies to:
- Devices with SNMP Object ID .1.3.6.1.4.1.10002.1 (Frogfoot MIB, which Ubiquiti at some point decided to use before they got their own Enterprise OID) or SNMP Object ID like .1.3.6.1.4.1.41112.* (Ubiquiti's own OID). Devices must also have a valid entry for OID .1.3.6.1.4.1.41112.1.4.1.1.9.1 (i.e. must have an antenna registered)
Notes:
- Just to avoid potential disappointment: This is not a template for Unifi Access Points. It is for AirMAX wireless bridges.
-
Ubiquiti UniFi SNMP Template
Applies to:
- A range of devices with Ubiquiti-style messy OIDs depending on firmware versions (things changed with firmware version 3.9.19):
- Devices with SNMP Object ID .1.3.6.1.4.1.10002.1 or SNMP Object ID like .1.3.6.1.4.1.41112.* if a valid result is returned for OID .1.3.6.1.4.1.41112.1.6.3.1.
- Devices with SNMP Object ID .1.3.6.1.4.1.8072.3.2.10 if a valid result is return for OI .1.3.6.1.4.1.41112.1.6.3.1.0.
- The Ubiquiti template applies to anything with either 10002 or 41112 match as well as 8072. In case of the latter, the system description also needs to start with UAP.
Notes:
- The pre/post 3.9.19 UniFi templates included in the XML both collect the exact same data. They only cater for the fact that Ubiquiti decided to change the OIDs used.
- A range of devices with Ubiquiti-style messy OIDs depending on firmware versions (things changed with firmware version 3.9.19):
-
-
-
@harun said in Sharing Standard Templates for NetXMS:
Cisco template
- cpu load
- memory utilization
- hardware monitoring
I downloaded this template, successfully imported it into NetXMS (v3.4.178), and it's automatically applying to my Cisco 1841 ISR router, but there are no DCIs when the xml template gets imported. Any ideas?
-
This is bug in importing templates from export files generated by old versions of NetXMS server. I just fixed it and fix will be included into next patch release.
Best regards,
Victor -
@paul said in Sharing Standard Templates for NetXMS:
Well - here is the first cut of my Windows generic template. it includes the events that are triggered.
For explanation of the thresholds that apply in this template, they are implemented as per here:
https://www.netxms.org/forum/general-support/simple-question-cdm-monitoring-using-snmp-anybody-doing-this/msg25843/#msg25843For excluding CD drives in discovery you have to exclude UFS as well...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login